Replace the loading on the frame by a single resultantforce. Suppose that F = 700 N, a = 0.5 m, andh = 1.3 m. . (Figure 1)Figureh200 NBYPart Cy =aSubmitFa200 NValueμAA1 of 1600 NRequest AnswerDetermine the magnitude of the resultant force.Express your answer to three significant figures and include the appropriate units.UnitsFR =SubmitPart BSpecify where its line of action intersects a vertical line along member AB, measured from A.Express your answer to three significant figures and include the appropriate units.THÅValueRequest Answer?Determine the angle between the resultant force and the x axis.Express your answer using three significant figures.ΑΣΦΗUnitsvecupward from A

Replace the loading on the frame by a single resultant force. Suppose that F = 700 N, a = 0.5 m, and h = 1.3 m. (Figure 1) Figure 200 N B a a 200 N < 1 of 1 600 N Determine the magnitude of the resultant force. Express your answer to three significant figures and include FR = Submit Part B μA Value Request Answer Units ?

Replace the loading on the frame by a single resultant force. Suppose that F = 700 N, a = 0.5 m, and h = 1.3 m. (Figure 1) Figure 200 N B a a 200 N < 1 of 1 600 N Determine the magnitude of the resultant force. Express your answer to three significant figures and include FR = Submit Part B μA Value Request Answer Units ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.5.10P: Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.

See similar textbooks

Similar questions

Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.
Four 10 kg masses are being supported by an 800mm solid rod. The rod is being supported at both ends, and the rest of the rod is suspended. Determine the smallest rod diameter to support the masses without bending the rod. Assume the Tensile Strength of the Rod material is 500 MPa
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20o Properties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2 L = 2.75 m
The forklift supports the engine. Determine the force that generates this load on element DB. Write your answer in Newtons. Consider Engine mass = 114 kg a = 1.47 m b = 1.81 m
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20oProperties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2
The 1900-NN load is applied along the centroidal axis of the member. (Figure 1) Determine the magnitude of the resultant internal normal force in the member section a-a. Express your answer to three significant figures and include the appropriate units. 2) Determine the magnitude of the resultant internal shear force in the member section a-a. Express your answer to three significant figures and include the appropriate units.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
a) Determine the tensile force T’ in the rope on the side connected to joint B: b) Determine the internal compressive normal force ƒBC in the tube BC: c) Determine the horizontal reaction force Rx and the vertical reaction force Ry in joint A: d) Determine the moment M of the center of bar AB: e) Determine the compressive stress σBC in the tube BC: f) Determine the critical load Pc for the tube BC: g) Which of the following statements about the tube BC is correct: A. The tube BC fails due to yielding B. The tube BC fails due to buckling C. The tube BC fails due to both yielding and buckling D. The tube BC is safe against both yielding and buckling h) Pin C has a diameter of 30 mm; calculate the shear stress τ of the pin C, when considering one cross-section for shear stress calculation:
The aircraft wing experiences bending, as shown above. Assume the weight and lift are as illustrated above. Assume the wing has a constant cross-sectional area of 10 m2, from wing root to tip. 1a) Describe all the various forces and stresses experienced by the aircraft wing. 1b) Compare how the various stresses, vary on the ground versus in flight. 2) Sketch the stress-strain diagram and indicate the position of the wing on it. Explain. 3) Describe the important material properties of the wing. Explain. 4) Draw and describe the Shear Force Diagram, from the wing root to the wing tip, as shown in the diagram. 5) The ultimate shear stress of the wing material is 20 kPa. Describe how the safety factor varies, from the wing root to the wing tip. 6) Draw and describe the Bending Moment Diagram, from the wing root to the wing tip, as shown in the diagram.
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?
– The weight is suspended from structural A–36 steel alloy and 2014-T6 aluminum alloy wires, eachhaving the same initial length of 10 ft and cross-sectional area of 7×10–3 in2 (Figure Q1). If the weight is increasedgradually, determine which wire yields first? Explain which material model and yield criterion you will use? Justifyyour choices
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.