Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. Answers: R= 240 N M = 315 N d = i Single resultant force. 210 N Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. i 9 i 670 mm 670 mm 670 mm N N.m mm

Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. Answers: R= 240 N M = 315 N d = i Single resultant force. 210 N Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. i 9 i 670 mm 670 mm 670 mm N N.m mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The Q-kg industrial door with mass center at G is being positioned for repair by insertion of the 5° wedge under corner B. Horizontal movement is prevented by the small ledge at corner A. The coefficients of static friction at both the top and bottom wedge surfaces are 0.66. Calculate the rightward force P' which would remove the wedge from under the door. Assume that corner A does not slip for your calculation of P'. Q = 402
Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(106) mm4. Use the moment-area method.
Using Force method analysis and with the use of virtual work method. Determine the internal moments acting in the beam at supports B and C. The wall at A moves upward 30 mm. Assume the support at A is a pin. Take E 200 GPa, I = 90(106) mm*.
consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips What is the shear force in the bottom beams (absolute value)? P1 = 2 kips What is the shear force in member EH (absolute value)? h = 11' What is the horizontal reaction at H (absolute value)? b = 25' What is the bending moment in the top beams (absolute value)? (please ignore black markings) What is the vertical reaction at I (tension positive)?
The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the cables BE and CD. The load applied at C. Determine the coordinates of D in the YZ plane so that the force in CD will be a minimum. Neglect the weight of the boom and cables. Answers: y = 16 ft; z = -34.7 ft
The force system on frame ABCDE is shown below. Replace the system by a force equal to the resultant of the three forces, acting vertically at B plus a couple acting horizontally at D and E.
The belt passing over the pulley is subjected to two forces F1 and F2, each having a magnitude of 40 N. F1 acts in the -k direction. Replace these forces by an equivalent force and couple moment at point A. Express the result in Cartesian vector form. Take θ = 45°.
Determine the resultant reaction in D in kN. using slope deflection method or moment distribution method. The loads are P= 60 kN, w= 20 kN/m and M=35 kN.m. Use E= 200 GPa and I= 300x10^6 mm4
d)Determine the internal torque (in N-m) in section B.
The force F = {6i + 8j + 10k} N creates a momentabout point O of MO = {-14i + 8j + 2k} N ⋅ m. If theforce passes through a point having an x coordinate of 1 m,determine the y and z coordinates of the point. Also,realizing that MO = Fd, determine the perpendiculardistance d from point O to the line of action of F. Note: Thefigure shows F and MO in an arbitrary position.
EI is constant (Assume EI= 1 kN-m^2) use moment area method 1.) determine the location of the maximum deflection from A2. ) determine the maximum deflection
Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(106) mm4. Use the conjugate beam method