Required informationFor a bolted assembly with eight bolts, the stiffness of each bolt is kb = 0.8 MN/mm and the stiffness of the members iskm = 2.6 MN/mm per bolt. The joint is subject to occasional disassembly for maintenance and should be preloadedaccordingly. Assume the external load is equally distributed to all the bolts. It has been determined to use M6 x 1 class5.8 bolts with rolled threads.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.Determine the maximum external load Pmax that can be applied to the entire joint without causing the members to come out ofcompression.The maximum external load for this case is 0.15625 N.

Kb = 0.8 MN/mm Km = 2.6 MN/mm no.of bolts N = 8 M6 x 1 class 5.8 bolt From the standard bolt data…

Answered: Required information For a bolted…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a concentric unfactored live load of 50 kips (dead load = 0) is required to be resisted by the connection and the bolt shear strength controls the design, the minimum required number of bolts is?
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?
An M30 × 3.5 ISO grade 8.8 bolt is used in a joint at a preload levelrecommended for reused connections, and the joint is subject to a repeated tensilefatigue load of P = 65 kN per bolt. The joint constant is C = 0.25.a) Determine the static load factors; b) The factor of safety guarding against a fatigue failure based on the Goodmanfatigue criterion
A 1/2-in-dia UNC, class 2 bolt with rolled threads is preloaded to 80% of its proof strength when clamping a 3-in-thick sandwich of solid steel. A static 1000-lb external load is applied. Part A Find the safety factor against static yielding. Express your answer using three significant figures. Part B Find the safety factor against joint separation. Express your answer using three significant figures.
Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Evaluate Yielding, Load and Joint Separation factor of safeties if the joint is permanently bolted.
Design of the Screw Jack. Lifting load – W, kN is 70. Hight of lifting– H, mm is 500 Types of threads is Square Material of nut is Cast iron
Draw the Mohr Circle and mark important points for a rod under pure tensile load & torsion
A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in diameter and 92mm thick and the flange web are 19 mm thick. Six 16 mm bolts in a 165 mm diameter circle connect the flange.The keyway is 6 mm shorter than the hub’s thickness and key is 14 mm x 14 mm. Coupling is to transmit 45 KW at160 rpm. For all parts, yield point value in shear is one – half the yield value which is 448 MPa. Calculate the forceon the shaft
Figure 8-19 is a cross-section of ASTM A36. A total of N bolts are to be used to resist a separating force of 7258.97N is one bolt. A) Determine kb,km, and C B) Determine the realized load factor for overload, the yielding factor of safety, and the load factor of joint separation.
How many bolts are required for LRFD and ASD for the bearing-type connection shown, if PD = 50 k and PL = 100 k? A325 3/4 in bolts, threads excluded from shear plane.
Determine the safe tensile load for fine series bolts of (a) M 24and (b) M 38. Assume that the bolts are not initially stressed and take the safe tensile stress as 450MPa.
(11) Find the power required to drive a power screw lifting a load of 40001b. A 2½-in double square thread with 2TPI. is to be used. The frictional radius of the collar is 2-in and the coefficients of friction are 0.l for the threads and 0.15 for the collar. The velocity of the nut is 10fpm .

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS