Required information Problem 09.097 - Modified Brayton Cycle with Two-Step Expansion - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS A gas-turbine power plant operates on a modified Brayton cycle shown in the figure with an overall pressure ratio of 8. Air enters the compressor at 0°C and 110 kPa. The maximum cycle temperature is 1500 K. The compressor and the turbines are isentropic. The high-pressure turbine develops just enough power to run the compressor. Assume constant properties for air at 300 K with cy= 0.718 kJ/kg-K, cp=1.005 kJ/kg-K, R= 0.287 kJ/kg-K, and k = 1.4. Combustion chamber Compressor High-pressure turbine Problem 09.097.b - Temperature and Pressure After High Pressure Turbine The temperature at state 4 is The pressure at state 4 is Low-pressure turbine Determine the temperature and pressure at state 4, the exit of the high-pressure turbine. (You must provide an answer before moving on to the next part.) K. kPa.

Required information Problem 09.097 - Modified Brayton Cycle with Two-Step Expansion - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS A gas-turbine power plant operates on a modified Brayton cycle shown in the figure with an overall pressure ratio of 8. Air enters the compressor at 0°C and 110 kPa. The maximum cycle temperature is 1500 K. The compressor and the turbines are isentropic. The high-pressure turbine develops just enough power to run the compressor. Assume constant properties for air at 300 K with cy= 0.718 kJ/kg-K, cp=1.005 kJ/kg-K, R= 0.287 kJ/kg-K, and k = 1.4. Combustion chamber Compressor High-pressure turbine Problem 09.097.b - Temperature and Pressure After High Pressure Turbine The temperature at state 4 is The pressure at state 4 is Low-pressure turbine Determine the temperature and pressure at state 4, the exit of the high-pressure turbine. (You must provide an answer before moving on to the next part.) K. kPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q#1. A gas-turbine plant operates on the regenerative Brayton cycle, the schematic diagram of whichis shown in Fig. Q 1, with two stages of reheating and two-stages of intercooling between the pressure limits of100 and1200 kPa . The working fluid is air. The air enters the first and the second stages of the compressor at 300 K and 350 K , respectively, and the first and the second stages of the turbine at 1400 K and 1300 K , respectively. Assuming both the compressor and the turbine have an isentropic efficiency of 80%. The regenerator has an effectiveness ofεregen=75% . Assume variable specific heats (i.e., use the concept of relative pressures) and the intermediate pressuresof intercooling and reheating is the square root of the product of inlet and exit pressures for intercooling and reheating. Make other the necessary assumptions and determine(a) the back work ratio,β , and the net work output,, wnet(b) the thermal efficiency (that is the first-law efficiency,ηi ) and(c) the…
Consider a simple Brayton cycle that uses air as the working fluid to operate a gas-turbine power plant between the pressure limits of 100kPa and 900kPa. Air enters the compressor at 298K and leaves at 610K at a mass flow rate of 1200kg/min. The maximum cycle temperature is 1380K. The net power output from the cycle is measured experimentally to be 55 MW. Assuming constant properties (Cv,Cp, R, and k) for air at 300K: a) Sketch a T-s diagram for the cycle b) Determine the isentropic efficiency of the turbine c) Determine the thermal efficiency
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. Determine the enthalpy of steam entering the reheater.
PART D only A gas-turbine power generator operates on an ideal air-standard Brayton cycle 1 → 2 → 3 → 4 shown in Fig. 1. The gas temperatures at the compressor inlet, compressor exit, and turbine inlet are T1 = 300 K, T2 = 600 K, and T3 = 1200 K, respectively. Solve PART D below using the variable specific heat assumption PART D - Evaluate the thermal efficiency η of the cycle and the back work ratio rBW = wC/wT.
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheatpressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, massflow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following:(a) ideal turbine work(b) ideal pump work(c) theoretical thermal efficiency(d) the steam rate(e) heat rate of the cycle(f) actual work of the pump if pump isentropicefficiency is 89%(g) actual turbine work if turbine isentropic efficiencyis 90%
First you selected a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications:• A pressure ratio of 10. • Heat is added to the cycle at a rate of 500 kW• Air passes through the engine at a rate of 1 kg/s• The air at the beginning of the compression is at 70 kPa and 0 C.Task 1Investigate the principles of operation for a gas turbine power plant by considering the following:1. Construct T-S and P-V diagrams while discussing the operation of a gas turbine power plant2. Describe the difference between closed and open gas turbine engine3. Explain how a closed gas turbine engine would be combined with a steam power plant. 4. Explain why Brayton cycle is more preferred over Rankin cycle in power plant stations? And how would you enhance the performance of a Brayton cycle?
Consider a regenerative Brayton cycle operating with a pressure ratio of 8, where the air enters the compressor at 300 K and 100 kPa, while it enters the turbine at 1060 K. Assume that both the compressor and turbine are isentropic, that speciﬁc heats vary with temperature, and that the regenerator has an effectiveness of 74%. Round all intermediate calculations to three decimal places. 1. What is the enthalpy at the turbine outlet in kJ/kg? Round your answer to two decimal places. 2. What is the enthalpy at the entrance to the heat exchanger that accepts external heat kJ/kg? Round your answer to two decimal places. 3. How much external heat is supplied to the cycle in kJ/kg? Round your answer to two decimal places. 4. What is the enthalpy at the entrance to the heat exchanger that rejects heat to the surrounding in kJ/kg? Round your answer to two decimal places. 5. How much heat is rejected to the surroundings in kJ/kg? Round your answer to two decimal places.
A regenerating brayton cycle that uses air as the fluid has a pressure ratio of 7. The minimum and maximum temperatures in the cycle are 30 ° C and 890 ° C. assuming an efficiency of 72% for the compressor, 82% for the turbine and an effectiveness of 62% for the regenerator. determine: a) the turbine air outlet temperature b) net labor output c) the thermal efficiency of the cycle
Q12) A stationary power plant operating on an ideal Brayton cycle has a pressure ratio of 8. The gas temperature is 300 K at the compressor inlet and 1300 K at the turbine inlet. Utilizing the cold-air standard assumptions, and assume the specific heats are constants. determine: a- The gas temperature at the exits of the compressor and turbine. b- The back work ratio. c- The thermal efficiency
Please use property tables. Thank you Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Report the amount of heat added in the reheat process, in kJ/kg, to one decimal place using rounding. 2. Report the amount of work produced in the low-pressure turbine, in kJ/kg, to one decimal place using rounding.
A power plant uses a gas-turbine to produce electricity. Assume that the gas-turbine operates on the ideal Brayton cycle has a pressure ratio of 8. The outside air temperature is 27 C and without preheating, the air is drawn into the compressor. The air compressed in the compressor and its pressure and temperature increase. Thereafter it is supplied into the combustion chamber where its temperature increases to 1023 C at constant pressure. Thereafter, hot air is drawn into the turbine. By considering the air-standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine (b) the back work ratio (c) the thermal efficiency
A steam power plant operates on the simple ideal Rankine cycle. The steam enters the turbine at 4 MPa and 500°C and is condensed in the condenser at a temperature of 40°C. draw and label the schematic diagram and the pV and TS planes. (a) Show the cycle on a T-s diagram. If the mass flow rate is 10 kg/s, determine (b) the thermal efficiency of the cycle (c) the net power output in kW.