Reservoir A, with surface level 75 m; above datum; supplies a junction through a 0.25 m, diameter pipe 1500 m long. From the junction a 0.25 m diameter pipe, 2250 m long feeds reservoir B, which is 37.5 m above the datum. A 0.25 m diameter pipe, 1000 m long feeds into reservoir C, 18.75 m above the datum. Take Fannings friction factor as f = 0.01 for all pipes. Apply Bernoulli's Between A & B, and simplify to the form used in the three tank problem QA² + QB Apply Bernoulli's Between A & C, and simplify to the form used in the three tank problem QA Qc²

Reservoir A, with surface level 75 m; above datum; supplies a junction through a 0.25 m, diameter pipe 1500 m long. From the junction a 0.25 m diameter pipe, 2250 m long feeds reservoir B, which is 37.5 m above the datum. A 0.25 m diameter pipe, 1000 m long feeds into reservoir C, 18.75 m above the datum. Take Fannings friction factor as f = 0.01 for all pipes. Apply Bernoulli's Between A & B, and simplify to the form used in the three tank problem QA² + QB Apply Bernoulli's Between A & C, and simplify to the form used in the three tank problem QA Qc²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump is required to move water at a design discharge of 1m3 /s between reservoirA to reservoir B (see schematic below). The difference in surface water elevations between A and B is10m. The difference in elevation between the surface elevation of A and the center of the first pipe sectionis 2m. The pipe is to be commercial steel with an internal diameter of 35cm. Determine the maximumdistance, LAP, from reservoir A that the pump could be installed without encountering cavitationproblems. Consider minor losses of a sharp-edged inlet. Assume a kinematic viscosity of 1x10-6 m 2/s and a specific weight of 9.79kN/m3 . Assume STP conditions (i.e., Pvapor = 3kPa, Patm=101.3kPa)
HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the reservoir. What is the maximum roughness height ε allowable for the pipe? Neglect minor losses.
Question 2) The centrifugal pump in the figure is in his preference Passing water at 25°C from the tank through the 1.22 m exchange store pumping. Inner diameter of the suction channel is 101.6 mm, in total it is 0.0306 and its length is 3.2 m. It the local coefficients of the user in the pipe are 7.4. If the pump works at a flow rate of 109 m3/h ENPY=1.52 is m. Does the pump work without cavitation at this flow? Show the calculation. For water, p=997 kg/m3 and Pb=3.169 kPa. Piping system at the entrance (Suction pipe) pump 22 Patm=101.3 kPa and 0.2=1.05. van
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
Water is pumped from a reservoir to a pressurized storage tank (P = 150 kPa gauge) atop a building by means of a centrifugal pump. There is a 70-m difference in elevation between the water surface in the reservoir and the end of the discharge line. The piping system consists of 80m of 5" SCH 40 steel pipe containing two 90o elbows, one gate valve, one rotary water meter, and six couplings from the reservoir to the pump; 3" SCH 40 steel pipe for 86m to the tank. The 3" pipe contains two gate valves, four 90o elbows, and ten couplings. It is desired to maintain a flow of water into the tank of 2.4 m3/min. Water temperature is 25oC. If the pump-motor set has efficiency of 65%, what would be the pumping costs be in pesos per day if electricity costs PhP 10.50/kW-hr?
Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m
Two pipes, one circular and one square have the same cross-sectional area. Which has the larger hydraulic radius ? Show your solution to prove your answer
A pump is fitted to 100 m pipeline that connects reservoir A reservoir B. The diameter of the pipe is 200 mm and is characterized by a fri factor of 0.02. The design discharge is 0.15 m³/s and the pump. Assuming th minor losses are 20% of friction losses, determine the head the pump must p
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. the total length and diameter of the sunction and discharge pipe are 500 mm,1500 m and 300 mm, 1000 m respectively. assumme a head lose of 2 meters per 100 m length of the sunction pipe and 3m per 100 m length of the discharge pipe. what is the required horsepower of the pump?
The tank–pipe system of Fig. is to deliver at least11 m3/h of water at 20°C to the reservoir. What is themaximum roughness height ε allowable for the pipe?