2. An A36 tension member is subjected to a service axial load of 1100 kN and a service moment of 30kN-m and 25 kN-m applied at major and minor axes, respectively. If the height of member is 1.20 m andrest on a continuous lateral bracing, check the adequacy of the steel section.W14 x 68;d = 356.62 mmti = 18.29 mmA = 12903 mm2tw = 10.54 mmbr = 254.89 mmSx = 1688 x 103mm3Sy = 397 x 103 mm3

Solution: Section details, ASTM steel designation type= A36 W14x68 Steel yield stress (Fy) = 248…

Answered: rest on a continuous lateral bracing,…

Engineering

Civil Engineering

rest on a continuous lateral bracing, check the adequacy of the steel section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A block of wood (s.g = 0.65) is 20 mm thick is floating in sea water (s.g = 1.03). find the area of…

Q: For a constant head laboratory permeability test on fine sand, the following values are given:…

Q: PROBLEM11.89 A ball is thrown so that the motion is defined by the equations x= 51 and y=2+61-4.9t2,…

A: Given x = 5t y = 2+6t-4.9t²

Q: but how to get 5/18 for question 2

A: Given data for question 2: V=110 kmph R=620 m f=0.12 e=? Given data for question 3: V=? R=620 m…

Q: 200 kN 25 kN/m A B Hinge Hinge |3 m+3 m+-6 m+ 6m 6 m-

Q: A concentrated point load of 200 KN acts at the ground surface. Find the intensity of vertical…

A: (a)Find the intensity of vertical pressure at a depth of 10 meters below the ground surface and…

Q: 3V/bh located at the midpoint of the altitude.

A: This question has been taken from mechanics

Q: Q3. For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…

Q: A canal is 80 km long and has an average surface width of 15 m. If the evaporation measured in a…

A: Given data: Stretch of evaporation, L = 80 km = 80000 m Average surface width, B = 15 m Evaporation,…

Q: Water flows at the rate of 25 in a trapezoidal channel having a base width of 3 m and side slope of…

Q: P7.29. Compute the rotation at B and the vertical deflec- tion at D. Given: E= 200 GPa, IAC= 400 =…

Q: 6 Core samples were taken randomly from a heterogeneous reservoir. The measured absolute…

Q: Find the resultant system of converging forces in the 500 N figure. Below 20ON

Q: Determine the SLOPE AND DISPLACEMENT at point A. TAKE E = || GPA. THE VALUE OF “I" CAN BE SOLVED BY…

Q: A W 360 x 744 is used as a beam to support a concrete floor system. The floor is to carry a total…

Q: Determine the slope at A and displacement at C. El is constant. 5 kN-m -1.5m- -1.5m-

Q: What is the flow of the main channel in m3/s if n = 0.020 and side slopes 2H:1V? What is the flow of…

Q: What are the active earth pressure coefficient and passive earth pressure coefficient of soil, if…

Q: Given the following data for three pipes in parallel: Pipe 1: D1 = 450 mm, L1 = 800 m ; Pipe 2: D2 =…

Q: Determine the maximum force P that can be applied to the specimen. The bar is made from steel and…

A: w=150 mmh=50 mmr=20 mmt=6 mmwh=15050=3rh=2050=0.4From graph, K=1.51σavg=σallK =1501.51…

Q: Determine the net length of crest and estimate the shape of downstream ogee spillway section having…

A: Solution-The giuven values are ,The elevation of crest =89.5mThe design discharge =1.15l/sThe number…

Q: A confined aquifer has a source of recharge. The hydraulic conductivity of the aquifer is 40 m/day…

Q: 2- A 8teel podis streteke between fwo pugid walls ard carries a tensile Coad f GO0ON a C. If the…

Q: A square footing 2 m x 2 m is located at a depth of 1.2 m below the ground surface. The soil…

Q: (a) What is SuperPave Method of mix design? What are the main advantages and disadvantage of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: What is the specific energy (m-kg/kg) for 1 m depth of flow having velocity of 3 m/s?

A: Given data: Depth of flow, y = 1 m Flow velocity, v = 3 m/s Acceleration due to gravity, g = 9.81…

Q: A square concrete conduit must transport 4.0 m³/s of water a distance of 45 m with a head loss of…

Q: Please explain how to do the marking for 30°incline plane, C4 x 4 and the center for M10 x1.5 on a…

Q: ely. The natural frequency

A: solution of above problem is below:

Q: Two objects of mass m1 = 10 kg and m2 = 5 kg are connected by a light, inextensible cord and hung…

Q: A gymnast with mass 50 kg suspends herself from the lower enc hanging rope of negligible mass. The…

Q: 25+b 20+c 50+b 1+a 15+d 1+c 5+a 1+b 10+b 1+d 20+c 1+c 1+a 1+a 1+b 1+d 1+b 1+c 1+d REACTION MAGNITUDE…

Q: There are many procedures in Quality Management. Give an example procedure in construction to…

A: Numerous functions are involved in construction projects spanning various activities and segments.

Q: c. Maximum shear stress on the bolts.

Q: 50 mm size is fixed in a horizontal pipe carrying water. The pressure gauge at entry read 137.34…

A: Pressure at entry =137.5kNm2Pressure at Throat=-0.375×13.6×9.81=-50.031kNm2Change in pressure…

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: 1. For the beam and loading shown, determine the maximum flexural stress (compression and tension)…

Q: For the soil specimėn shown in figure, calculate the soil permeability if rate of flow is 2 cc/min.…

Q: How useful are concrete hollow blocks in construction and why is it important?

A: These are standard sized blocks which are hollow in the centre and are used to reduced the dead…

Q: What are the active earth pressure coefficient and passive earth pressure coefficient of soil, if…

Q: w = Wo-kc? 8kw/m B. am 4m

Q: QLIn the figure given below calculate the of (H) for the given data: H. f1= di= L1= F2= D2= L2=…

Q: Heavy fuel oil flows from A to B through 3000 ft of horizantal 6-in steel pipe. The pressure at A is…

A: Given data Pipe diameter is equal to 6 inch Pressure At A is equal to 155 PSI Pressure at b is…

Q: A fluid flows through a 100 m long and 120 mm diameter tube. In 2 minutes 0.15m3 of fluid passes…

Q: The beam supports the loads as shown in the figure. Using E=200 GPa, w = 22 kN/m, P = 35 kN and M =…

Q: 9. The magnitude of the vertical reaction force at support A is most nearly?. a) 1.3 kN b) 5.0 kN c)…

A: Asked: To determine the magnitude of the vertical reaction force at support A. We will be using…

Q: 20ド Sm 10m

Q: Q2: For the soil profile and loading condition shown in Figure (2). Find: a) Final consolidation…

Q: P7.1. Derive the equations for slope and deflection f daflootion at B wi

Q: A gate slanted 60 degrees from the horizontal with width = 1.6 m and height = 2.4 m is submerged by…

Question

2. An A36 tension member is subjected to a service axial load of 1100 kN and a service moment of 30
kN-m and 25 kN-m applied at major and minor axes, respectively. If the height of member is 1.20 m and
rest on a continuous lateral bracing, check the adequacy of the steel section.
W14 x 68;
d = 356.62 mm
ti = 18.29 mm
A = 12903 mm2
tw = 10.54 mm
br = 254.89 mm
Sx = 1688 x 103mm3
Sy = 397 x 103 mm3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a Knuckle joint to transmit 170kN. Allowable stresses in tension, shear and compression are75 N/mm2in tension, 65 N/mm2 and 140 N/mm2 respectively.
If the applied shear force V=10,605 lbs, determine the maximum horizontal shear stress (in ksi) acting on the member. Use x=1in, y=5in. Round off to two decimal places
Evaluate the given Fink Truss using method of sections. Answer the following questions if ϴ = 30°, Ф = 60°, and the distance, d = 12 ft. What is the reaction at A? What is the force at in member BD? What is the force at in member FE? What is the force in member CE?
Determine the largest shear force V (kips) that the member can sustain if the allowable shear stress is fv = 8.4 ksi. d = 3.6 in
Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the I-section shown. Find the load (p in kN/m) this beam can carry on a span of 4 m, distributed over its length if the permissible stress in bending is 12 MPa and in shear 0.8 MPa.
Calculate the stresses in members AB, DF, and BD. Given:FAB = 51.22 kN (C)FDF = 50 kN (C)FBD = 32.98 kN (C)d = 0.05 m
A truss joint shown consists of a bottom chord C made up of two angles and web members A and B each carrying the given loads. Using rivets with allowable shearing and bearing stresses of 120 MPa and 600 MPa respectively, determine the number of rivets for members A, B, and C. thickness = 9.5 mm ; diameter = 18 mm
For the truss shown, determine the force in members BD, CD, and CE stating whether the member force is in tension or compression. Wherein: Q=2 T=6 Example: 2QT kN = 226 kN T.Q5 m = 4.25 m
A truss joint shown consists of a bottom chord C made up of two angles and web members A and B each carrying the given loads. Using rivets with allowable double - shearing and bearing stresses of 120 MPa and 600 MPa respectively, determine the number of rivets for members A, B, and C. thickness = 9.5 mm ; diameter = 18 mm
Determine the stress on member DF for the given truss if all of the members are 75 mm by 100 mm steel sections. CHOICES ARE: 4. 327 MPa Compression 4.327 MPa Tension 1. 763 Mpa Compression 1. 763 Mpa Tension 7. 532 Mpa Compression 7. 532 Mpa Tension 2.4 Mpa Compression 2.4 Mpa Tension 1. 442 Mpa Compression 1. 442 Mpa Tension
The I-section displayed is made up of five boards (four 40x40mm and one 40x380mm). If the allowed stress in bending is 12 MPa and in shear is 0.8 MPa, calculate the load (p in kN/m) that this beam can carry over a span of 4 m, dispersed over its length.
25. If the applied shear force V = 15,520 lbs, determine the maximum horizontal shear stress (in ksi) acting on the member. Use x = 2 inch, y = 5 inch. ROUND OFF TO TWO DECIMAL PLACES.