Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and θ = 55°. Determine the shear stress in pin A and pin B and the normal stress in rod (1). Express your answer in MPa rounded to the nearest hundredths.

Q: ᴀɪʀ ᴀᴛ ᴀ ᴛᴇᴍᴘᴇʀᴀᴛᴜʀᴇ ᴏꜰ 33°ᴄ ʜᴀꜱ ᴀ ʀᴇʟᴀᴛɪᴠᴇ ʜᴜᴍɪᴅɪᴛʏ ᴏꜰ 50 ᴘᴇʀᴄᴇɴᴛ. ᴅᴇᴛᴇʀᴍɪɴᴇ (ᴀ) ᴛʜᴇ ᴡᴇᴛ ʙᴜʟʙ…

A: Given Dry air temperature = 33o C Relative humidity = 50% To find Wet bulb temperature Dew point…

Q: The long bolt passes through the 20-mm-thick plate. If the force in the bolt shank is 9 kN,…

A: Given data: ● The force applied on the bolt shank: F = 9 kN = 9000 N ● The thickness of the plate…

Q: 4Q. Compute the capillary depression of mercury at 68 °F (0 = 140°) to be expected in a 0.05 in…

A: Given:   Temperature of mercury, T=68 deg F Angle, Q=140 deg Diameter of the tube, d=0.05 in

Q: PROBLEM 1. A steel block shown is supported by two rods anchored on a ring. What is the resultant of…

A:

Q: 1. Conceptualize a research problem using gap analysis.

A: given; (1) gap analysis should be used for meet the target of production according to requirement in…

Q: 2-11. Determine the plastic distorts as shown by the dashed lines. 3 mm y C 300 mm the shear strain…

A:

Q: 3 if its subjected to double shear, determine the average shear stress in the pin. Take P= 610 16…

A: Given date 1) Load (P) =610 lb 2) Diameter of pin =0.25 in To find:- Average double shear stress at…

Q: Required information Deformable rods BD and CF are attached to a rigid rod ABC as shown. Rod BD is…

A:

Q: A helicopter that is hovering d = 750 ft from a highway and is tracking a speeding car traveling at…

A: Given: d=750 ft v=120 mph = 176 ft/s a=8 ft/s2 r = 900 ft To find: angular velocity angular…

Q: The resultant force has higher effect on the body than the group of forces when it replaces False O…

A: The resultant force has higher effect on the body than the group of forces when it replaces. Answer:…

Q: A- Four kg of water is placed in an enclosed volume of 1 m3. Heat is added until the temperature is…

A: Given that: m = mass of water = 4 kg V = volume of enclosed container = 1 m3 Heat is added until the…

Q: How did you get the summation of forces in each direction?

A: We can easily find the vector form of each force and then consider the sum of all the forces acting.…

Q: A- One kg of steam with a quality of 21% is heated at a constant pressure of 201 kPa. The work done…

A: Given data as per questionMass of steam, m=1 kgQuality of steam=21%Pressure of steam, P=201 kPaWork…

Q: IF load : 100N and Effort force : 500N How can we calculate Fulcrum force?? Do anyone have a good…

A: GivenLoad=100NEffort force =500N

Q: In air pipline, the flow has the following conditions at section 1: 25C. 1.8 bar, 15 m/s velocity,…

A:

Q: Suppose that F= 720 lb. (Eigure 1) Figure 1 of 1 Y Part A Determine the magnitude of the resultant…

A:

Q: (1)The brake mean effective pressure? (2) the mechanical effeciency

A:

Q: ood work on the promblem but the process is a bit hard to read, can you express

A: Given data as per question Tensile axial force, F=4500 N Outer diameter of tube, do=25 mm Inside…

Q: In the P-V diagram shown the work done by the system is equal to: p(N/m²) 2 + 10 9 ~ ∞0 ∞ 9 10 11 12…

A: P-V diagram of a cycle is shown in the figure. It is required to determine the work done by the…

Q: La Paz, Bolivia, is at an altitude of approximately 2743.2 m. Assume a standard atmosphere. How high…

A:

Q: Problem#2: Determine the reactions of the beam. 300 lb 100 lb/ft R1 8' R2 400 lb

A: Detailed explanation and solution of the above problem uploaded in below pictures.

Q: Two reversible cycles are in series, each process doing the same net work, Wcycle. The first cycle…

A: Given data: Higher temperature (TH)=1000°RLower temperature (TL)=400°R Need to determine the…

Q: What is the pressure difference between points A and B?

A: Given that,  Relative density of oil (Soil)= 0.85 Density of oil ρ = relative density of…

Q: Consider the stress element below. (a) Determine the three principle stresses and three shear…

A: given; stress in x direction(σx)=130MPa (tensile)stress in y direction(σy)=90MPa (tensile)stress in…

Q: iving along a highway at 80 km/h, a 15-m long truck driving at 60 km/h is exactly 10 m ahead of you.…

A: Given data as per questionSpeed of car=80 km/hSpeed of truck=60 km/hLength of truck =15 mDistance…

Q: Given: • A (1030.00 N, 990.00 E), B (1040.00 N, 1120.00 E) • ZA= 51° 54'41", ZB = 53° 12'46" • AC =…

A: given data:- coordinate of point A(1030.00 N, 990.00 E) coordinate of point B(1440.00 N, 1120.00 E)…

Q: A: Figure (1) shows an open-water tank has two rectangular gates. If the density is 1000 kg gates is…

A: Givenρ=1000 kg/m3w=1.5m

Q: For the rotation in two dimensions, both energy, and angular momentum is quantized.  Select one:…

A: in the solution two dimensions both energy and angular momentum is conserved.

Q: The geared system shown in Figure P3.19 represents an elevator system. The motor has an inertia I,…

A:

Q: If the length of the side of a body-centered cubic structure is 300 pm, what is the radius of the…

A:

Q: A- List three differences between the dynamic pump and peristaltic pump?

A: There are two types of pumps are given. Differences between the dynamic pump and the peristaltic…

Q: Measures that can be taken to improve the boiler efficiency ?

A: Requirements to increase the efficiency of the boiler :

Q: Car A is traveling at a location where the speed limit is 100 km/h. The police officer in car P…

A:

Q: words, describe the difference between the magnitude of a vector and the direction. In addition,…

A:

Q: In what way are non-ferrous metals more advantageous than ferrous metals?

A: This question is based on the concept of ferrous and non ferrous metals.

Q: The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam…

A:

Q: L₁ Rigid bar ABCD is supported by two bars as shown. There is no strain in the vertical bars before…

A: Calculate the contraction in bar (2).

Q: B: Drive an equation could be used to calculate liquid volumetric flow rate for rectangular open…

A: Introduction:- The volumetric flow rate is the flow of volume per unit of time. that means in a unit…

Q: The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55…

A:

Q: Molybdenum has a BCC crystal structure, an atomic radius of 0.1363 nm, and an atomic weight of 95.94…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked.…

Q: A 25-cm-diameter stainless steel ball (p = 8055 kg/m³, Cp =480 J/kg °C) is removed from the oven at…

A:

Q: How is Determining the tensile strength of material relevant in mechanical engineering applications?

A: A tensile strength of any material is the maximum load that a specimen made of any particular…

Q: A part made from hot-rolled AISI 1212 steel undergoes a certain amount of cold-work operation. If…

A:

Q: Calculate the ratio of the radiant energy emitted from a surface at 37ºC and an adjacent surface of…

A: Given: The surface temperature, T1 = 37 C The adjacent surface temperature, T2 = 35 C

Q: The command p560.fk Select one: True

A: In 1978, the Puma 560 robot (programmable universal manipulator for assembly) was introduced and…

Q: What is the magnitude of the distributed load. Units are taken as [N]. Do not include units in your…

A:

Q: Determine the reactions at the supports:

A: Draw the free-body diagram of part BC. Apply moment equilibrium about B.…

Q: Determine the reactions of the beam. 300 lb 100 lb/ft D1 8' D2 400 lb

A:

Q: A certain factory has an average electrical load of 1500 kW and requires 3.5 MJ/s for heating…

A: Average Electric Load, = 1500 kW Required Load, = 3.5 MJ/s Initial pressure, P1 = 15 bar Initial…

Q: Air is contained in a rigid container has a pressure of 0.6 bar vacuum. If the atmospheric pressure…

A: