Problem 20.28Rod AB is attached to the rotating arm using ball-and-socketjoints as shown in (Figure 1). AC is rotating with a constantangular velocity of wAC = 8.5 rad/s about the pin at C.Assume d = 6 ft.Figure201.5 ft3 ft@AC< 1 of 1 ▼Part ADetermine the components of the angular velocity of link BD at the instant shown.Enter your answers in radians per second to three significant figures separated by commas.V ΑΣΦΗ ΤΗ(WDB)z. (WDB)y. (WDB)= =Submit Request Answervec 5?rad/s

Answered: Image /qna-images/answer/a3e64378-08ef-4d30-83f9-30dde30a71e3.jpg

Rod AB is attached to the rotating arm using ball-and-socket joints as shown in (Figure 1). AC is rotating with a constant angular velocity of wAC = 8.5 rad/s about the pin at C. Assume d = 6 ft. Figure 2A 1.5 ft 3 ft LAC < 1 of 1 >

Rod AB is attached to the rotating arm using ball-and-socket joints as shown in (Figure 1). AC is rotating with a constant angular velocity of wAC = 8.5 rad/s about the pin at C. Assume d = 6 ft. Figure 2A 1.5 ft 3 ft LAC < 1 of 1 >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flywheel absorbs 2500 ft-lb of energy at a coefficient of fluctuation of 0.10. The mean diameter of the flywheel is 72 inches. The weight of the arms and hub is 12 % of the rim weight. The mean rim speed is 80 fps. Consider the specific weight of the flywheel as γ = 0.26 lb/in3. A. Find the mean rpm of the rim. B. Determine the weight of the rim. C. What is the cross sectional area of the rim?
A flywheel is fitted to a multi cylinder engine, which runs at a mean speed of 360 r.p.m. If the speed varies from 6 % above the mean to 2 % below it and the fluctuation energy is 1200 kN-cm, If the radius of gyration is 20 cm, find (i) mass moment of inertia of the wheel and (ii) mass of flywheel. The mass moment of Inertia in Kgm2 is Mass of the flywheel in kg is
(ii) A cam, with a minimum radius of 25 mm, rotating clockwise at a uniform speed is to be designed to give a roller follower made of 20mm diameter at the end of a valve rod, motion described below : 1. To raise the valve through 58 mm during 122° rotation of the cam by simple harmonic motion 2. To keep the valve fully raised through next 32° 3. To lower the valve during next 66° by uniform acceleration and retardation. Determine the maximum velocity and acceleration of the valve rod when the cam shaft rotates at 104 r.p.m and write the remaining dwell angle.
An engine flywheel has a mass of 6.5 tones and the radius of gyration is 2 m. If the maximum and minimum speeds are 120 r. p. m. and 118 r. p. m. respectively, find maximum fluctuation of energy.
The turning moment diagram for a petrol engine is drawn to the following scales: turning moment 1 mm to 2·5 Nm; crank angle, 1 mm to 1°. The fluctuations of energy between the crank positions for minimum and maximum speeds corresponds to an area of 600 mm² of the turning moment diagram. The flywheel is made from cast iron, of density 7·2 tonnes/m3. Determine: (a) The greatest fluctuation of energy (b) The mass of the flywheel required to prevent the a fluctuation of speed greater than ± 0·5% from the mean speed of 1600 rev/min if the radius of gyration is 120 mm. (c) The dimensions of the flywheel (diameter and thickness) (d) Describe the possible consequences to the system if the flywheel was not used to limit the fluctuation of speed.
A flywheel of mass 0.9 ton is fitted to a multi cylinder engine, which runs at a mean speed of 380 r.p.m. If the speed varies from 9 % above the mean to 6 % below it and the fluctuation energy is 1100 kN-cm, find (i) mass moment of inertia of the wheel and (ii) radius of Gyration.
(11) A 120cm diameter diamond circular blade, mounted on a pulley-driven steel shaft, is requiring a blade peripheral linear speed of 45m/s. Motor drive is 100kW @ 1,200rpm with 150mm drive pulley. Determine: (a) the shaft rpm to attain blade peripheral speed required; (b) the shaft diameter; (c) the shaft pulley diameter.
Power is transmitted between two pulleys mounted on the parallel shafts rotating in the opposite direction. The pulleys are separated apart at a distance of 1950mm having 0.45m and 0.2m diameter respectively. What power can be transmitted by the belt when the larger pulley rotates at 200 rev/min, if the maximum permissible tension on the tight side of the belt is 1000 N, and the value of µ between the belt and pulley is 0.25. Design the length of the belt required and the angle of contact between the belt and each pulley.
Q.1 In the mechanism depicted in Figure Q1 the upper end, A, of a vertical rod is attached to fixed bearings that allow it to rotate in the vertical, yz, plane at angular velocity ω1 = 4 rad s^-1 . At the lower end of this rod a bearing B can rotate about it at angular velocity ω2 = 6 rad s^-1 . Also attached to this bearing is another rod currently aligned parallel to the horizontal, y, direction. A collar, C, is sliding towards the free end, D, of this other rod at 3 ms^-1 . Determine, at the instant shown:- (a) the linear velocity of the collar, (b) the linear acceleration of the collar.
a steam engine runs at 150rpm. its turning moment diagram gave the areas in mm2 taken in order above and below the mean torque line is 500,250,270,390,190,340,270,250, the scale for turning moment is 1mm=500mnm, 1mm=5’ if the fluctuation of speed is not to exceed +or-1.5% of mean, determine a suitable diameter and cross-section of the rim of flywheel with axial dimension equal to 1.5times the radial dimension. the hoop stress is limited to 3mpa and the density of material of flywheel is 7500kg/m3.
power (N)=9.9kw Input speed (n1)=2350rpm Distance between centers (a)=168mm Total distance between Ave B bearings=440mm module(m)=3mm question 3 Calculate the power on the output shaft since there is 3% loss in gears in gearboxes, rolling bearings in support bearings (2% loss in a pair of bearings) and sealing element spring seal (4% loss in a pair of sealing elements).
.A cast iron flywheel with mean radius of 250 mm runs at average of 100 rad/s and has a maximum fluctuation of energy ∆KE of 2500 N-m. If the coefficient of fluctuation of speed of 0.01. which of the following is the mass of the flywheel rim? choices: 400 kg 100 kg 25 kg 4 kg