Rod AB is made of a mild steel that is assumed to be elastoplastic with E = 200 GPa and oy =250MPA . After the rod has been attached to the rigid lever CD, it is found that end C is 6 mm too high. A vertical force Q is then applied at C until this point has moved to position C'. Determine the required magnitude of Q and the deflection 8, if the lever is to snap back to a horizontal position after Q is removed. 9-mm diameter 1.25 m B 6 mm - 0.7 m- 0.4 m

Rod AB is made of a mild steel that is assumed to be elastoplastic with E = 200 GPa and oy =250MPA . After the rod has been attached to the rigid lever CD, it is found that end C is 6 mm too high. A vertical force Q is then applied at C until this point has moved to position C'. Determine the required magnitude of Q and the deflection 8, if the lever is to snap back to a horizontal position after Q is removed. 9-mm diameter 1.25 m B 6 mm - 0.7 m- 0.4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid beam is suspended from two steel rods as shown and is initially horizontal. BF bar with a cross section of 143 . The midpoint of the beam is deflected 10 mm downward by the slow application of the force , after which the force is slowly removed. Knowing that the steel used for the rods is elastoplastic with and determine (a) the required maximum value of and the corresponding position of the beam, (b) the final position of the beam.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 67 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E = 180 GPa. Assume a = 3.1 m, b = 1.3 m, and c = 1.3 m. What is the magnitude of load P that is necessary to displace point A 10 mm to the left?
Determine the x, y, z components of internal loading at a section passing through point B in the pipe assembly. Neglect the weight of the pipe. TakeF1 = {100i - 200j - 300k} N and F2 = {100i + 500j}N.
Solve this Portion Use problem 3.52. Add a force of 500 kN that is perpendicularly applied at point B in the direction from B towardC.Remove the torque.The steel and brass are assumed to have Poisson’s ratios of 0.30. (a)Determine the internalforce in AB.(b)Determine the internal force in BC.(c)Determine the deflection at Point B.(d)Determine thereaction at Point A.(e)Determine the reaction at Point C. Explain your work concisely and in detail
line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (10 -6)m 4 , and if this section is under a bending moment of 22 kN m, please calculate the normal stress at Point B: ____ MPa. Calculate your answer to 1 decimal place.
A tripod is shown in the figure consists of three members AB, AC and AD whose lower ends are in the xy plane. Member AB is subjected to a compressive force of 700 N. Determine the following: 1. Force in member AC.2. Force in member AD.3. Vertical load P.
A tapered rod with length c = 7m and cross - sectional dimensions a = 270n mm and b = 119 mm is carrying an axial load P = 75kN . If the modulus of elasticity of the rod is E = 164GPa , determine the elongation of the rod in mm . Final ans. in 3 dec place
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = 8200 N, what is the maximum and minimum shearing stress developed in the rivet.
The cantilever beam above is made up of concrete with E = 70 MPa, refer to the table below for the properties and loads for the beam: Given: b(mm) = 250 h(mm) = 400 w(kN/m) = 15 Mb(kN-m) = 45 Using area moment method, determine the following: 1. Vertical reaction at A, RA. 2. Moment reaction at A, MA. 3. Flexural rigidity of the beam in N-mm^2 4. Rotation at B, in degrees. 5. Rotation at C. in degrees. 6. Deflection at B in mm. 7. Maximum deflection of the beam in mm. 8. If a concentrated load will be placed at B to remove the deflection at C, determine the magnitude of this load in kN.
The rigid beam ABC is suspended from two steel rods as shown and is initially horizontal. BF bar with a cross section of 143 mm^2 . The midpoint B of the beam is deflected 10 mm downward by the slow application of the force Q, after which the force is slowly removed. Knowing that the steel used for the rods is elastoplastic with E=200 GPa and σ_Y-300 MPa, determine (a) the required maximum value of Q and the corresponding position of the beam, (b) the final position of the beam.
The pedestal shown is formed by two concrete blocks with a circular cross section. Block A has a diameter of 0.5 m and a height "a" of 0.5 m, while block B has a diameter of 1 m and a height "b" of 1.3 m. Considering the elastic modulus of the concrete E is 25 GPa, and that P1 is worth 8 MN, find the value of the force P2 that produces a deflection at the top of the pedestal of 4.39 mm. Do not consider the weight of the blocks and express the result in MN (Mega Newton) with a decimal approximation Don't use chat gpt