The figure shows three 0.0112 kg particles that have been glued to a rod of length L-5.97 cm and negligible mass. The assembly can rotate around a perpendicular axis through point O at the left end. If we remove one particle (that is, 33% of the mass), by what percentage does the rotational inertia of the assembly around the rotation axis decrease when that removed particle is (a) the innermost one and (b) the outermost one?

The figure shows three 0.0112 kg particles that have been glued to a rod of length L-5.97 cm and negligible mass. The assembly can rotate around a perpendicular axis through point O at the left end. If we remove one particle (that is, 33% of the mass), by what percentage does the rotational inertia of the assembly around the rotation axis decrease when that removed particle is (a) the innermost one and (b) the outermost one?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter4: Temperature Effects On Atom Arrangements And Atom Motion

Section: Chapter Questions

Problem 32CQ

See similar textbooks

Similar questions

DYNAMICS OF RIGID BODIES PROBLEM: In a amusement park ride, gondola cars of weight W are attached by rods 24ft long to a bull wheel 20ft in diameter. The bull wheel rotates in a horizontal plane about a vertical axis at its center. At how many rpm is it rotating when the supporting rods of the gondolas are inclined at 30° with the vertical? Consider each gondola to be a particle concentrated at the end of each 24ft rod.
1. Calculate the reaction at A in kN.0 2. Calculate the reaction at E in kN.0 3. Calculate the deflection at B in mm. No need to type the sign and the unit of your answer.0 4. Calculate the slope at B in radians. Express your answer in x10-3. No need to type the sign and the unit of your answer.0 5. Calculate the deflection at C in mm. No need to type the sign and the unit of your answer.0 6.Calculate the deflection at D in mm. No need to type the sign and the unit of your answer.0 7. Calculate the slope at D in radians. Express your answer in x10-3. No need to type the sign and the unit of your answer.0 8. Calculate the deflection at E in mm. No need to type the sign and the unit of your answer.0
In Figure below if a metlic c:ube of a 1 2 inch side length weighing 46 kg, floats at a two layer fluids mercury and sea water. Detennine the position of the block at mercury- water interface when it has reached equilibrium. (mass density of sea water ; 63.92623 lb/fts) and for mercurv : 845 lb/ftS).
Determine the x and y components of reaction at A using scalar notation and also the magnitude of reaction at B.mass = 27 kg and neglect thickness of the bar
Using the Conjugate Beam Method What is the reaction components of the beam? Whereas, E=200GPa I=800x10^6 mm^4 P= 259.5 KN
Determine the mass moment of inertia of the assembly about the z axis. The density of the material is 7.85 Mg/m3.
A particle starts from rest at a position x(0) = 0. Find the velocity v(t) and position y(t) of the particle if it is subjected to the following accelerations:a) a(t) =6t3-4t2+7t-8b) a(t) = 5e-5t +1/4 cos(1/4)t
Locate the centroid of the volume of the solid shown where a hemesphire of radius r is mounted on top of a right circular cylinder of the same radius and altitude h
Explain about the reaction mass in the statnamic test.
A BUS IS HAVING A SPEED OF 140 km/hr, IN A PERIOD OF 6 SECONDS, THE BUS DECREASED ITS SPEED TO 100 km/hr. CALCULATE THE RATE OF DECELLERATION.
determine the unit weight in the loosest and densest packing of 2mm diameter spheres which have specific gravity of 2.7
The height of kerosene in the left leg was measured as 8.2 cm high and 5.2 cm on the right leg. The difference in elevation between the interfaces of kerosene and water measured 2.5 cm. Determine the specific gravity of kerosene.*