Oil flows from a tank through 150 m of 150 mm pipe and then discharges into air as shown. If the head loss from pt. 1 to pt. 2 is 600 mm, determine the pressure needed at pt. 1 to cause 17 Liters/sec of oil to flow. El. 30 m Air, p El. 20 m Oil S = 0.84 a. 87.74 kPa b. 24.73 kPa c. 60.66 kPa d. 36.58 kPa 150m-150 mm Ø

Oil flows from a tank through 150 m of 150 mm pipe and then discharges into air as shown. If the head loss from pt. 1 to pt. 2 is 600 mm, determine the pressure needed at pt. 1 to cause 17 Liters/sec of oil to flow. El. 30 m Air, p El. 20 m Oil S = 0.84 a. 87.74 kPa b. 24.73 kPa c. 60.66 kPa d. 36.58 kPa 150m-150 mm Ø

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.) 39.5136 b.) 12. 9517 c.) 99.9358 d.) 30. 4889 2. What gage pressure p1 in kPa, is needed to provide the given flow rate? a.) 1121kPa b.) 1328kPa c.) 1692kPa d.) 1725kPa
A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.
A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using n= 0.019 Choices: A. 1210.47 B. 1012.74 C. 2101.74 D.112.47
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. A. 12.9517 B. 39.5136 C. 99.9358 D. 30.4889 What gage pressure p1 in kPa, is needed to provide the given flow rate? A. 1121 kPa B. 1725 kPa C. 1692 kPa D. 1328 kPa
oil (SG = 0.88) dischargesfrom a pipe (D = 13 in.) through a sharp-crested, round orifice (diameter = 5 in.), as shown. the coefficients of contraction and velocity are 0.619 and 0.967, respectively. find the actual velocity (in ft/s) in the jet. Point (1) is a point collinear with the orifice at point (2). Point (3) is the free surface of the manometer containing mercury. use h = 2.84 ft., and y = 7.42 in.
1. Compute the head loss in a pipe with diameter 300 mm for a length of 15,000 meters and carrying a flow of 0.097, if f=0.02. (Hint: Use h=(0.0826fL(Q^2))/(D^5)
1. A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using f=0.029 Group of answer choices 928.44 428.94 284.94 892.44
Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downwardsuch that a 75mm-dia. exit orifice is 0.60m lower than the upper end. Assume no friction loss. The sharp edged orificehas a coefficient of contraction of 0.65. What is the pressure at the point A in KPa?
Oil (s = 0.91) flows through a pipe, passing point 1 with 250mm diameter, then point 2 with 100mm diameter. A differential mercury gage connected at the points shows a deflection of 350mm. Determine the discharge, in L/s, of the oil in the pipe assuming C = 0.63, and point 1 and point 2 have the same elevation.
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
Show the necessary figures (if applicable) 2.3) Points A and B are separated by 915 m of new 152.4 mm diameter cast iron pipe. 50 lps of water flow from point A to point B. Point B is 18.5 m above point A. What must be the pressure at point A if the pressure at point B is 345 kPag and the head loss between A and B is 54 m? 2.4) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Water flows in a wide channel at Fr=4.5 and y1 = 2.40 m. If the flow undergoes a hydraulic jump, calculate: y2