s relative density is 0.85, its dynamic viscosity is 1.5 Pa.find the pumping power that must be supplied to the fluid so that the mineral oil, which is s, can flow continuously with a flow rate of 10.8 m3/h through a horizontal stainless steel pipe with a length of 50 m and a diameter of 40 mm. The roughness value of stainless steel ε= 0.002

s relative density is 0.85, its dynamic viscosity is 1.5 Pa.find the pumping power that must be supplied to the fluid so that the mineral oil, which is s, can flow continuously with a flow rate of 10.8 m3/h through a horizontal stainless steel pipe with a length of 50 m and a diameter of 40 mm. The roughness value of stainless steel ε= 0.002

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = Answer J / kg. c. Energy Loss at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement for the pump is kg ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 10 m3 / hr. The pipe length is 35m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer b. Loss of Energy along the straight pipe = Answer J / kg. c. Losing Energy at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement of the pump ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
Send 20 degree Celsius of water at 4.0 [m3 / h]. How many inches of standard steel pipe should be used to set the average flow rate in the pipe to 1.5 ~ 2 [m / s]? At this time, determine the average flow rate and the flow of the fluid.
Oil that has a density of 880 kg/m3 flows under a head of 30 m. The pipe that the oil flows through is 3000 m long and 0.35 m in diameter. Due to the cooling along the span of the pipe the viscosity changes, this may be taken as 0.57 kg/m-s over the first 1500 m and 1.14 kg/m-s over the second 1500 m. Confirm that laminar flow conditions exist and calculate the flow in dm³/s. Neglect entry and exit losses.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3/hour. The length of the pipe is 35m and there are 2 elbows. Calculate the pump power requirement. The properties of the solution are density 975 kg/m3 and viscosity 4x 10-4 Pa s. a. Reynolds number = b. Energy Loss along a straight pipe = J/kg. c. Energy Loss in turns = J/kg. d. Total energy to overcome friction = J/kg. e. Energy to raise water to height = J/kg. f. Theoretical energy requirement of the pump kg ethanol/second = J/kg. g. Actual pump power requirement = watt.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = AnswerJ / kg. c. Losing Energy at curves = AnswerJ / kg. d. Total energy to overcome friction = AnswerJ / kg. e. Energy to increase water according to height = AnswerJ / kg. f. The theoretical energy requirement of the pump ethanol / second = AnswerJ / kg. g. Actual pump power requirement = Answerwatt.
Complete the missing columns in the table and determine the experimental and theoretical values of the pipe friction factor using the respective formulae given above. Take the kinematic viscosity of water as 8.92x10-7 m2/s.
Density of oil = 900kg/m3kinematic coefficient of viscosity ν = 0.00001m2/s fluid flows at qv = 0. 2m3/s Length = 500 m oDimaeter = 200-mm Determine: (a) the head loss and(b) the pressure drop if the pipe slopes down at 8 in the flow direction.
A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the me- ter is 100 mm and the pressure at the throat is 400 mm of mercury below atmosphere. If 3% of the differential pressure is lost between inlet and the throat, determine the flow rate of the pipeline. PLEASE USE BERNOULLI'S ENERGY EQUATION. INCLUDE COMPLETE SOLUTION
Water is flowing in the pipe at a flow rate of 0.736 m^3/s. There are four 45-degree elbows in the pipe. Surface illumination: 0.0001524 m. Find the diameter of the pipe. Coefficient of water kinematic viscosity: 1.12*10^-6 m^2/s.
Water at 20∘C∘C having the density of ρw�� = 998.3 kg/m3kg/m3 and kinematic viscosity of νw=1.00(10−6)m2/s��=1.00(10−6)m2/s is pumped from a lake into the tank on the truck using a 50-mmmm-diameter galvanized iron pipe with ε� = 0.15 mmmm (Figure 1). The pump performance curve is as shown in (Figure 2). The total length of the pipe is 50 mm. Determine the maximum volumetric flow the pump will generate. Include the minor losses of the five elbows. Express your answer to two significant figures and include the appropriate units.