S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.

S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A built-up beam made from fastening two channels to a wide flange section carries loads` as shown. The fasteners are 12mm∅ bolts with allowable shear stress τ= 110 MPa. For bearing, σb= 220MPa for single shear, and σb= 275 MPa for double shear. E=200 GPA. Fy=420 MPa. 6. Determine the horizontal shearing stress at 20 mm above the Neutral Axis. 7. Determine the horizontal shearing stress at 95 mm above the Neutral Axis. 8. Determine the spacing of the bolts.
A simply supported concrete beam 6m long is reinforce with four-28 mm diamgram tension bars. The beam has a width of 300mm and over all depth of 400.the steel covering to the centroid of the renforcement is 70 mm fc=30mpa and fy 418mpa A .draw a stress diagram B.compute for the ultimate capacity of the beam
•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm
A wood beam AB on simple supports with spanlength equal to 10 ft is subjected to a uniform load ofintensity 125 lb/ft acting along the entire length of thebeam, a concentrated load of magnitude 7500 lb acting ata point 3 ft from the right-hand support, and a momentat A of 18,500 ft-lb (see figure). The allowable stresses inbending and shear, respectively, are 2250 psi and 160 psi.(a) From the table in Appendix G, select the lightestbeam that will support the loads (disregard theweight of the beam).(b) Taking into account the weight of the beam(weight density = 35 lb/ft3 ), verify that theselected beam is satisfactory, or if it is not, selecta new beam.
A beam cast monolithically with the slab thickness of 110 has a span of 4 m spaced at 6 m center to center. The width of the web is 300 mm and effective depth of 500 mm. It is reinforced on the tension side with 8-20 mm Φ rebars. Fc’ = 30 MPa fy = 310 MPa 1. Which gives the effective width of flange? a. 2000 mm b. 1500 mm c. 2500 mm d. 1000 mm 2. Which gives the depth of the compression stress block? a. 30.55 mm b. 32.56 mm c. 12.45 mm d. 42.14 mm
The overhanging beam shown supports the given ultimate load Wu= 5okN/m. The section is 300mm by 500mm rectangular beam having f'c=35MPa, fy=420 MPa, stirrups diameter = 10mm and concrete cover 40mm. a.) Calculate the vertical reaction at B in kN b.) Calcute the vertical reaction D in kN c.) Calculate the area of steel reinforcement corresponding to rho max in mm^2. d.) Calculate the location of the point of zero shear in the beam measured from the left support B in mm. e.) Calculate the maximum positive moment in the beam in kN.m.s
The beam shown here is made of wood with an allowable shear stress of τall = 1100 psi. If PB = 5 kips, determine the maximum allowable force PC that can be applied on the structure before the beam fails in shear.[LAB= 2 ft, LBC= 2 ft, LCD= 1.5 ft, b = 1.25 in., h = 7 in.] Determine the maximum value of the first moment of area (Q) for the beam. (in^3) Determine the maximum allowable force at C (PC) that can be applied on the structure before it fails in shear. (kips)
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Thickness, tf=9mm Flange Width, B=112.5 mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear 1. Determine the location of centroid, ȳ, from top of the beam in mm
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. Determine the maximum flexural stress on the beam in MPa. Determine the maximum shearing stress on the beam in MPa.
Calculate the stresses in members AB, DF, and BD. Given:FAB = 51.22 kN (C)FDF = 50 kN (C)FBD = 32.98 kN (C)d = 0.05 m