Using the principles of Mohr's circles for the soil element shown, Determine: a. Maximum and minimum principal stresses b. Maximum shear stress, Tmax c. Average normal stress d. Normal and shear stresses if element is rotated as shown in the figure 5.4 kN/m² 1.9 kN/m² + -3.5 kN/m² + 50° 1.9 kN/m²

Using the principles of Mohr's circles for the soil element shown, Determine: a. Maximum and minimum principal stresses b. Maximum shear stress, Tmax c. Average normal stress d. Normal and shear stresses if element is rotated as shown in the figure 5.4 kN/m² 1.9 kN/m² + -3.5 kN/m² + 50° 1.9 kN/m²

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.4P

See similar textbooks

Similar questions

3. The following convergence measurements (U) have been made in a 4.6-m-diameter circular vertical shaft in good quality granitic rock mass (Em = 40 GPa, ν = 0.2): θ (deg) U (mm) 0 2.25 45 2.39 90 1.50 135 1.00 a) Derive the equations that relate convergence to in situ stress. b) The angle θ is measured (clockwise) with respect to the x-axis, which is oriented 30 degrees clockwise from True North. What is the orientation of the maximum principal stress with respect to True North?
The soil profile at a site is shown Figure P16.3. Find the total horizontal normal stresses at A and B, assuming at-rest conditions.
The soil stress state is shown in the figure, σx = 10 kN/m2, σy = 50 kN/m2, τxy = -10 kN/m2:(1) Please use Mohr circle to draw the soil stress state(2) Calculate the maximum principal stress σ1 and the minimum principal stress σ3(3) Please find the (pole) position(4) What is the angle of intersection between the maximum principal stress surface and the horizontal plane?
Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure P6.2). Determine the increase in vertical stress at a depth of 6 m below point A. Use Boussinesq’s equation.
Point loads of magnitude 9, 18, and 27 kN act at A, B, and C, respectively(Figure 6.27). Determine the increase in vertical stress at a depth of 3 mbelow point D. Using Westergaard solution. Use μs = 0.4.
Determine the shear stress at points A, B, C andD for the following section. Also determine the maximum shear stress, then plot the shear stress distribution. Given: V = 10 kN.
Using the principles of Mohr’s circles for the soil element shown in Figure 10.36, determine the following:a. Maximum and minimum principal stressesb. Normal and shear stresses on plane AB
Using Boussinesq’s Equation determine the vertical stress increase ΔϬz, at point C at a depth 3.0 meters , if the point loads at A,B and D are 200 KN, 400KN and 600KN respectively. ΔϬzC =_____________KN/m2.
A point within an embankment slope has a vertical normal stress (v) of 100 kPa, a horizontal normal stress (x) of60 kPa, and a horizontal shear stress (xy) of 20 kPa.(a) Determine the major and minor principal stresses.(b) Determine the orientation of the major principal stress (in degrees from vertical, clockwise, orcounterclockwise.(c) Draw the Mohr Circle and schematic of the element stress state
Q#5: From the Tri –axial test, determine the effective normal stress on the plane of Maximum shear stress. Explain why the shear failure occurred along the plane with angle 54.73 and not along the plane of maximum shear stress. Take σ’1 = 552, σ’3 = 276, ø’ = 19.45?
Q#5: From the Tri –axial test, determine the effective normal stress on the plane of Maximum shear stress. Explain why the shear failure occurred along the plane with angle 54.73 and not along the plane of maximum shear stress. Take σ’1 = 552, σ’3 = 276, ø’ = 19.45? Find σ’ = ? τf = ? τ: ?
Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point), then find the stresses inclined at: 1- 75° from the horizontal plane. 2- With the horizontal plane.