Section F Type your answer. A sealed rig (1 m3) contains 2 kg of water (liquid PLUS vapour) at 20°C. The rig is heated until the temperature inside is 95°C. Calculate: 44 The quality of steam at 95°C. (%) Type your answer. Тур 1 45 Internal energy at 20°C. (kJ/kg) Type your answer. 46 Internal energy at 95°C. (kJ/kg)

Section F Type your answer. A sealed rig (1 m3) contains 2 kg of water (liquid PLUS vapour) at 20°C. The rig is heated until the temperature inside is 95°C. Calculate: 44 The quality of steam at 95°C. (%) Type your answer. Тур 1 45 Internal energy at 20°C. (kJ/kg) Type your answer. 46 Internal energy at 95°C. (kJ/kg)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.3P

See similar textbooks

Similar questions

An inventor claims to have devised a process using only saturated steam at 100C which by a complicated series of steps, make heat continuously available at T of 177C. He claims further that, for every kilogram of steam taken into the process, 1800 kJ of energy as heat is liberated at this higher T of 177C. Show whether or not such a process is possible. In order to give the inventor the benefit of any doubt, assume cooling water to be available in unlimited quantity at 0C. topic: introduction to chemical engineerint thermodynamics
A throttling steam calorimeter is an instrument used for the determination of the quality of wet steam flowing in a steam main line. It utilizes the fact that when wet steam is throttled sufficiently, superheated steam will form. If wet steam at 200 psia is throttled in a calorimeter to 15 psia and 300 oF, determine the quality of the wet steam.
What is the specific internal energy of water at 50 kPa and 200°C?
A cylinder-piston device provided with stops, so that the water supports the weight of the piston, and the force of the atmosphere,It contains water, initially at 300 kPa and 0.5 m3 / kg. The water is heated to a saturated steam condition and the plunger rests on the stops. With the plunger on the stops, the water is heated up to the pressure of 600 kPa. In the P-V and T-V diagrams, with respect to the saturation lines, the process curves go through the initial and final states of the water. On both T-V and P-V diagrams draw the isotherms that pass through both states, and show their values in ° C, in the isotherms. (see img 1)
Air at a rate of 1000cfm is cooled from 80⁰Fdb and 70⁰Fwb until it is saturated at 55⁰F. Determine the amount of moisture removed (lb/min), sensible heat removed (BTU/min), total heat removed (BTU/min), and the sensible heat factor.
3.0 kg of steam at a pressure of 100 kPa are contained in a rigid sealed tank of volume 5.95 m3. The steam begins to cool as heat is transferred to the atmosphere. When the internal pressure reaches 10 kPa, the tank walls will collapse.a) What is the initial temperature of the steam in the tank (in oC)?b) What will the temperature be in the tank when the walls collapse (in oC)?c) Attheinstantofcollapse,whatisthemassofwaterinthevapourandliquidstate (in kg)?d) Deduce the work done for this process
One pound of steam at 260°F contains 80% steam and 20% liquid water. How much heat will be released by this steam when it is allowed to condense to water at 200°F? Answer must be 811.6 BTU
An insulated evacuated tank of 1.75-m> volume is attached to a line containing steam at 400 Wa and 513.15 K (240°C). Steam flows into the tank until the pressure in the tank reaches 400 kPa. Assuming no heat flow from the steam to the tank, prepare graphs showing the mass of steam in the tank and its temperature as a function of pressure in the tank
15 - Some water is compressed from 1 atm pressure to 4 atm pressure at constant temperature. The initial density of water is 1000 kg/m³. Since the isothermal compressibility of water is α =4.8x10-5 atm-1, what will be the density change at the end of the compression process? a) 1,153 kg/m³ B) 1.74 kg/m³ NS) 1,872 kg/m³ D) 1,105 kg/m³ TO) 1,101 kg/m³
Complete the blank cells in the following table of properties of steam. In the last column, describe the condition of steam as compressed liquid, saturated mixture, superheated vapor, or insufficient information, and, if applicable, give the quality
27.259 kg per second of water at 0.03398675 kbarg and internal energy of 15000 kW is heated at constant pressure to saturated vapor and further heated at constant volume process until the pressure is quadrupled. Determine the ratio of the heat added during the constant volume process to the heat added during the constant pressure process. Use steam tables of Keenan et al.
Many gyms and health clubs have steam saunas, which are small steam-filled rooms. Traditionally, steam saunas have a container of heated rocks. A small ladle of water is poured on the rocks in order to make the steam. Use what you have learned so far about heat transfer to explain how hot rocks can be used to make steam? Why do you think only a small ladle-full of water is poured on the rocks at one time?