Answered: Select a double angle member to resist…

Select a double angle member to resist a tensile load of 50 kN dead plus 100 kN live. The member is 2.5m long and is assumed to be connected with one row of 20 mm Ø bolts.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.2.6P

See similar textbooks

Related questions

Q: 5- An abrupt rise of 0.8 m was designed to control a hydraulic jump generated after a 4 m wide…

A: Abrupt rise = 0.8 mWidth of sluice gate = 4 mOpening = 0.2 mFlow discharge = Flow depth = 1.2 mTo…

Q: Determine the volume of the products of hydration and gel/ space ratio for a mix contains 125 gm…

A: Cement quantity= 125 gm Water quantity= 35 ml Hydration took place in sealed specimen. We have to…

Q: P8.2 A copper wire of diameter d = 2 mm is coiled around a spool of radius r. The elastic modulus of…

A: Given data,diameter of coil (d) = 2 mmelastic modulus of copper (E) = 117 GPa Yield strength = 310…

Q: A reinforced-earth retaining wall is to be 10 m high. The following data are given: 1.25 m;…

A: Given data,H=10m

Q: Request: use Excel Spreadsheet Classical_Settlement_Shallow.xls to finish the homework and print out…

A: Given data,B=6ftD=2ftP=100k

Q: Determine the displacement ad rotation at start and end point of the beam 6 kN/m 2 m 2 m 6 kN/m B 2…

Q: A 23-in. vertical rod CD is welded to the midpoint C of the 50-in. rod AB. Determine the moment…

Q: 9 kN-m 33 kN/m A By (KN): Cy (KN): C₁: C₂: EIBA (+): 2m 2 kN/m C +im -3 m- EISA (1+): Előo (1+):.…

A: Slope:Slope refers to the change in the angle or inclination of a structure, typically a beam or a…

Q: dị 200 mm a

Q: Please answe

Q: Please solve this question queckly

Q: P8.20. (a) Compute the vertical deflection and slope of the cantilever beam at points B and C in…

A: E = 4000 Kips/in.2 Determine the vertical deflection and slope at B and C. Determine the minimum…

Q: Volume of measure, (ft³) Weight of measure (lb) Weight of measure + aggrega

Q: A treatment plant treats water at an average daily flowrate of 2.7 m3/s. The water is chlorinated…

A: Given data,average daily flowrate of 2.7 m3/sChlorine concentration = 3 mg/LChlorine decays at a…

Q: A column 12" square with fc'=5 ksi reinforced with 8#10 bars of fy=60ksi,support a service load of…

A: Footing:Footing could be a sort of foundation that's constructed with concrete or brickwork masonry…

Q: A four story "intermediate reinforced concrete moment frames" supports seismic weights of 1400 kip…

Q: A car travels along the level curved road with a speed which is decreasing at the constant rate of…

Q: A flat steel bar has axial loads (forces along the centroidal axis of the bar) applied at points A,…

Q: B TIM F Compute vertical displacement at C using conjugate beam method method.

Q: Determine the end moments that can safely be carried by a UC 254 x 254 x 107 in S355 steel, assuming…

A: The objective of the question is to determine the end moments that can safely be carried by a UC 254…

Q: A shovel of size (0.75) m³ intended to be used to load ordinary soil to trucks. What is required to…

Q: How does road transportation benefit the industry?

A: Road transportation is beneficial for many industries because it helps in the faster delivery of raw…

Q: For the uniform beam shown, use superposition to determine the reaction at each of the three…

A: A simply supported continuous beam is shown in the above figure. A point load of P and another point…

Q: solution

A: As there are multiple questions posted, according to the guidelines only the first three are being…

Q: A municipal water treatment plant employs two circular primary clarifiers arranged in parallel,…

Q: Q.No.3: Determine the ACI design moment capacity of the beam shown in the Figure 2 if the fe-4000…

A: The compressive strength of the concrete is .The yield strength of the concrete is .The area of…

Q: (a) Complete the table below for the three slope and flow classifications: Relationship between…

A: TypeRelationship between Normal depth (dn) and Critical depth (dc)Type of slopeType of…

Q: awing 18 kW of electric power while pu nd outlet diameters of the pipe are 8 c easured to be 250 kPa…

Q: State and explain the qualities of good cement.

A: It is always desirable to use the best quality cement in the various constructions. Therefore, all…

Q: 5. Determine the maximum allowable tensile load (20% dead load, 80% live load) for a single C15x33.9…

A: Dead load (DL) = 20% = 0.2TLive load (LL) = 80% = 0.8TSingle C 15x33.9 section1/2 in. gusset…

Q: A frame and loading are shown. B P 120 mm 120 mm D 120 mm 90 mm Determine the force acting on member…

A: Given:P = 320 NRequired:Force at C

Q: How can I calculate the water level in a grit chamber at average flow and at peak hourly flow. The…

A: Average daily flow rate, Width of tank, Length, Depth, Elevation, To find: Water level in a grit…

Q: can you help me please the solution is to find a deflection at B P = 250 kg, a = 0.7 m, E = 2x10^6…

A: E = 2 × 106 kg/cm2 Determine the deflection at point B.

Q: A vertical parabolic curve has a grades of g1= 4% while g2=6%, what the grade at the third quarter?

A: Initial grade (g1) = 4%Final grade (g2) = 6%In a vertical parabolic curve, the grade changes…

Q: Applying the (AMM) Area Moment Method Approach. Consider 150 mm x 200 mm section and E = 80 GPa.…

Q: 9-21. Determine the reactions at the supports. Assume A is fixed and the joint at B is rigid. EI is…

Q: Construct the shear and moment diagrams for the loaded beam shown. After you have the diagrams,…

Q: A concrete mix includes 360kg cement and 162kg water per cubic meter and no admixture is used. The…

A: A concrete mix includes the following ingredients per cubic meter:a. Cement = 360 kgb. Water = 162…

Q: Trusses and Frames (Method of Joints, Sections, Member) Determine the magnitude of the force (in kN)…

A: The truss shown in the above figure. We have to find out the magnitude of the force (in kN) in…

Q: GIVEN: Truss loaded with dead, live and wind. 500 lb 1000 lb 1000 lb DEAD LOAD 1000 lb 1000 lb 1000…

A: To calculate :Analyze the truss

Q: - Find the moment at B. A 25 kN/m 12 m I B 6 m E = constant 250 KN Į C 1.51 6 m D

A: Given:Required:Moment at B

Q: Please answer the following and fill up the table using Principle of virtual work method only.…

A: A beam is loaded is as followsdeflection at joint A has tobe found out

Q: 1) For the state of stress shown in figure, use the Mohr's circle method to determine (a) The…

A: Normal stress about x-axis, Normal stress about y-axis, Shear stress, To find: (a)…

Q: - A moderately sinuous curved trapezoidal cha carrying a discharge of Q-35 m³/s. The long…

Q: Please

Q: How do you get the valuse for V mid and V mean?

Q: neodolite traverse carried line of a proposed tunnel re ag obtained: Bear 086° Line A-(i) (i)-(ii)…

Q: Problem #3: Determine the force in members AF, BF, and BC, and state if the members are in tension…

Q: 5.17 For the beam and loading shown, determine the maximum normal stress due to bending on a…

Q: TA B C 3m + 3m 3 m P₁ P₂ 3m D Consider the truss shown in (Figure 1). Set P₁ = 9 kN, P₂ = 10 kN, and…

Question

Select a double angle member to resist a tensile load of 50 kN dead plus 100 kN live. The member is 2.5m long and is assumed to be
connected with one row of 20 mm Ø bolts.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Procedure for selecting a Double angle member:

VIEW

Step 2: Determine the factored load

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Give me right solution Select a single angle member to resist a tensile load of 60 kN dead plus 40 kN live. The member is 2.5m long and is assumed to be connected with one row of 20 mm ∅ bolts.
Select a single angle member to resist a tensile load of 60 kN dead plus 40 kN live. The member is 2.5m long and is assumed to be connected with one row of 20 mm ∅ bolts.
Select a W-section to resist a tensile load of 400 kN dead plus 800 kN live. The member is to be 6.00 m long and is connected through its flange only. Assume that there can be as many as four bolts on any one cross-section (two in each flange)
For the clevis connection shown, determine the shear stress in the 20-mm-diameter bolt for an applied load of P = 130 kN.
Use A36 steel and select a single-angle tension member to resist a service dead load of 13 kips and a service live load of 45 kips. Assume that the member will be connected to a 3⁄8- inch-thick gusset plate with a single line of five 7⁄8-inch diameter bolts. The member is 15 feet long. Note that the block shear strength failure must be consider for the design.
Determine the resultant load on the most stressed bolt in the eccentrically loaded connections shown, using the elastic method.
Determine the required diameter of the bolts to be used in the bracket shown if it has a allowable shearing stress of 93 Mpa. The bracket carries an eccentric load of 50 kN.
Select a 30-ft-long W12 section of A992 steel to support a tensile service dead load PD = 130 k and a tensile service live load PL = 110 k.As shown in Fig. 4.1, the member is to have two lines of bolts in each flange for 7/8-in bolts (at least three in a line 4 in on center).
Select a single-angle tension member of A36 steel to resist a dead load of 28 kips and a live load of 84 kips. The length of the member is 18 feet, and it will be connected with a single line of 1-inch-diameter bolts, as shown below. There will be for or more bolts in this line.
Select the lightest WT180 available to support a factored tensile load of 1112 kN. Assume there are two lines of M22 bolts in the flange (at least three bolts in each line 100 mm on center). The member is to be 9.144 m. Use LRFD.
Select a 9-m long W10 section of A572 Grade 50 steel to support a tensile load of PD = 490 kN and PL = 580 kN. The member is assumed to have one line of holes in each flange and two lines of holes in the web for 19 mm diameter bolts. There will be four bolts in each line 100 mm on center. Neglect block shear
Select an ST shape to be used as a 20 ft long tension member that will safely support the service tensile loads:PD = 35 k,PL = 115 k, and PS = 65 k (snow). The connection is through the flange with two lines of three 3/4-in Ø bolts 4 in on center.Use A572 Grade 50 steel. Neglect block shear.