Select a single-angle tension member of A36 steel to resist a dead load of 28 kips and a live load of 84 kips. The length of the member is 18 feet, and it will be connected with a single line of 1-inch-diameter bolts, as shown below. There will be for or more bolts in this line

Select a single-angle tension member of A36 steel to resist a dead load of 28 kips and a live load of 84 kips. The length of the member is 18 feet, and it will be connected with a single line of 1-inch-diameter bolts, as shown below. There will be for or more bolts in this line

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.2.6P

See similar textbooks

Related questions

Q: Determine the smallest net area of the tension member shown in Fig. P3-17.The holes are for 3/4-in Ø…

Q: Determine the Net Area for the following Plate Section consider all possible Cases. The Plate…

A: To find net area

Q: USING LRFD, DETERMINE THE ff: 1. LOAD P that the angles can carry against tensile yielding in the…

A: Given : Breadth of the plate, B = 200 mmThickness of the plate, t = 10 mmDiameter of bolts, d = 20…

Q: 3. A Channel section is connected to a 10mm gusset plate with 20mm- diameter bolts as shown in the…

A: Consider the given data Grade of steel=A572 Gr 50Member designation=C 12×25Gross area of section,…

Q: 3. Select an A992 10-ft long channel member that can resist a service load of 128 kips (DL:LL=3:2).…

Q: Determine the effective net area of the W16 x 40 shown in Fig. P3-23. Assume the holes are for…

A: Given: W16×40. From the properties, Ag=118 in2.tf=0.505 in.bf=7 in.d=16 in

Q: For the eccentric shear loading of the accompanying figure, two vertical lines of % inch diameter…

Q: A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate…

A: Given: 1⁄2 × 5-inch plate of A588 steel. ⇒Width, b=12in⇒Thickness, t=5 in Diameter of bolts = 5⁄8…

Q: Calculate at what length this tension member would cease to satisfy the recommended slenderness…

Q: For the tension member shown is made of 12 mm x 240 mm plate attached to gusset plate, Fy 248 MPa,…

A: Plate size 12 x 240 mm,Fy = Yield strength of steel = 248 MPaFu = Ultimate strength of steel = 400…

Q: For the two lines of M20 bolts shown in the figure, determine the design tensile strength (kN) of…

A: given- a bolted section required- to calculate design strength.

Q: lines of M20 bolts shown in the figure, determine the pitch (s) in mm that will give it a net area…

Q: A bracket cut from a W310X179 is connected to a W310X179 column flange with 12 A325 bearing-type…

A: Brackets are the projections which carry loads. The bracket which is connected to a support must…

Q: An L 150 x 100 x 16 is used as a tension member, with one gage line of 20 mm bolts in each leg at…

Q: snip

A: a.) Calculate the gross area of one flange as follows Afg=tfbf Here, bf is the width of flange and…

Q: 1. A single-bolted double-cover butt joint is used to connect two plates which are 8 mm thick.…

A: Solution: Given Data: Assume 16 mm dia bolt of grade 4.6 and cover plates to be 6 mm thick

Q: Select the lightest W12 section available to support working tensile loads of PD = 120 k and PL=288…

Q: A single-angle tension member, an L3 1⁄2 × 3 1⁄2 × 3⁄8, is connected to a gusset plate with…

Q: Select the lightest S section that will safely support the service tensile loads D = 92 kips and L =…

A: The given data is shown below: D=92 kipsL=56 kipsLength of member=20 ftDiameter of bolt=34in.A36…

Q: Select a pair of C10 channels for a tension member subjected to a dead load of 120 kips and a live…

A: Given: Dead load, DL = 120 Kip Live load, LL = 275 Kip Grade of steel = A588 Grade 50 Span of…

Q: An L 175 x 175 x 20 is used a tension member, with one gage line of 22 mm bolts in each leg at the…

A: dh = db + 3 = 22 +3 = 25mm B = 90 +110 +90 +60 = 350mm

Q: An L8 × 4 × 3/4 with two lines of 3/4-in Ø bolts in the long leg and one line of 3/4-in Ø bolts in…

Q: Determine the effective net area using the U values given on Table 3.2 An MC12x45 is connected…

Q: Compute the net area. The tension member shown in Figure P3-14 contains holes for 1-in Ø bolts.At…

A: Given:- diameter = 1in To find:- net area

Q: Design a tension member (16 ft. long) of the type, as shown in Figure 1. It is connected to a gusset…

Q: Determine the value of “b” in millimeters. 2. Determine the net area for tension in plates in square…

Q: A tension member with a length of 22 feet must resist a service dead load of 216 kips and a service…

A: You didn't specify which method to use. I have solved using LRFD.

Q: Compute the maximum acceptable service load on an A36 steel plate tension member 1/4 in. x 12 in.…

A: Given: A36 steel 7/8 in dia bolts 1/4 in X 12in

Q: The tension member shown in Figure P3-14 contains holes for 7/8-in Ø bolts. At what spacing, s, will…

Q: Calculate the number of bolts required at the end connections of the angle to the gussets using 20…

Q: Example (3-10): Select a 30 ft - long W12 section of A992 steel to support a tensile service dead…

Q: 3. Select an A992 10-ft long channel member that can resist a service load of 128 kips (DL:LL=3:2).…

Q: The 7/8 × 14 plate is shown in the figure. The holes are for 7/8-in Ø bolts. Compute the net area of…

A: Given Data:- Thickness of plate=7/8 in Width of plate=14 in Diameter of holes=7/8 in To find:-…

Q: For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui. For…

A: Solution: Given: load = 85 kips Direct shear: V=855=17 kips Find the centroid location: x=3×35=1.8…

Q: Compute the net area of each tension member. Note that for a standard-size bolt hole, hole dia =…

Q: 3. fa 400N force is applied to the short bracket shown below interpret the load as a force and a…

Q: The 1 × 8 plate is shown in the figure. The holes are for 3/4-in Ø bolts. Compute the net area of…

A: Given that, width of plate, B = 8 in the thickness of the plate, t=1 in diameter of the bolt, d=…

Q: draw a connection containing 6 bolts of diameter 16mm type A325x to connect two plates each plates…

A: Since the question comprises of a number of subparts, the solution for first three subparts are as…

Q: A WT8X50, Fy =50 ksi has two lines of 7/8" bolts as shown below. There are 4 bolts in each line, 3"…

A: The ASD allowable strength Pn' is calculated by the formula given below; Pn'=PnΩ→eq(1) Here, the…

Q: The tension member shown in Figure is an L6 × 3 ½× 5/16. The bolts are ¾ inch ameter. If A36 steel…

Q: 2 in Ø bolts W12 × 40-

Q: Design number of Structural bolts required to hold three plate sections of 12” x 0.5” each. The dead…

A: Given Data: The dimensions of each plate section is, A=12''×0.5'' The dead load at the connection…

Q: A W18 × 35 with two holes in each flange and one in the web, all for 7/8-in Ø bolts. Compute the net…

Q: What will be minimum number of bolts required in each row for a suitable bolted bracket connection…

A: Given data,

Q: An MC12 x 45 is connected through its web with 3 gage lines of 7/8-in Ø bolts. The gage lines are 3…

A: Schematic diagram of the given problem:

Q: An angle with staggered fasteners in each leg is shown in Figure 3.17. A36 steel used, and holes are…

A: An angle with staggered fasteners in each leg is shown in Figure. A36 steel is used, and holes are…

Q: For the connection shown, the average shear stress in the 16-mm-diameter bolts must be limited to…

Q: Determine the effective net area of the W16 × 40 shown in the figure. Assume the holes are for…

Q: 10. A 20 mm diameter, A325 bolt, is subjected to a tension force of 15 kN due to dead load and 50 kN…

A: Solution: Given: For Tension: Dead Load (D.L)=15KN Live Load (L.L)=50KN Tensile Load= 1.2D.L+1.6L.L…

Q: 3. A 2L4x4x1/2(3/8 in. separation). ASTM A36, has one line of (3) 4-in. dimeter bolts in standard…

Question

Select a single-angle tension member of A36 steel to resist a dead load of 28 kips and a live
load of 84 kips. The length of the member is 18 feet, and it will be connected with a single line
of 1-inch-diameter bolts, as shown below. There will be for or more bolts in this line.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 14 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Select a 30-ft long W12 section of A992 steel to support a tensile servicedead load of 130 kips and a tensile service live load of 110 kips. Asshown in the figure, the member is to have a two lines of bolts in eachflange for 7/8-in bolts (at least three in a line 4 in. on center).Use Fy = 50 ksi and Fu = 65 ksi.
Select a 30-ft-long W12 section of A992 steel to support a tensile service dead load PD = 130 k and a tensile service live load PL = 110 k.As shown in Fig. 4.1, the member is to have two lines of bolts in each flange for 7/8-in bolts (at least three in a line 4 in on center).
A single angle tension member, L 4 x 4 x 3/8 in. made from A36 steel is connected to a gusset plate with 5/8 in. diameter bolts, as shown in Figure below. The service loads are 35 kips dead load and 15 kips live load. Determine the adequacy of this member using AISC specification. Assume that the effective net area is 85% of the computed net area.
Give me right solution Select a single angle member to resist a tensile load of 60 kN dead plus 40 kN live. The member is 2.5m long and is assumed to be connected with one row of 20 mm ∅ bolts.
Using ASD, select the lightest double-angle tension member to resist a service dead load of 30 kips and service live load of 90 kips. Use A36 steel. The member will be connected with two (2) lines of 7/8-inch Ø bolts, A325, placed at the usual gauge distances. There will be more than three (3) bolts in each line. The member is 25 feet long and will be connected to a 3/8-inch thick plate.
Use A36 steel and select a single-angle tension member to resist a service dead load of 13 kips and a service live load of 45 kips. Assume that the member will be connected to a 3⁄8- inch-thick gusset plate with a single line of five 7⁄8-inch diameter bolts. The member is 15 feet long. Note that the block shear strength failure must be consider for the design.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
Design a 11 ft single-angle tension member of A992 steel, to support a dead tensile load of 25k and a live tensile load of 45k. The member is to be connected to one leg only with 5/8-in bolts (4 in a line 3" on center) Then assume a reasonable distance for bolts to the edge of the angle and check the block shear. *Please clearly show all steps so I can follow along.
A 2L 3 x 2 x ¼ LLBB tension double angle, A36 steel is subjected to a dead load of 12 kips and a live load of 36 kips. It is attached to a gusset plate with a line of 3/4-inch diameter bolts through the long legs. Does this member have enough stamina? Assume Ae= 0.85 in. Use LRFD.
The tension member shown in Figure is an L6 × 3 ½× 5/16. The bolts are ¾ inch ameter. If A36 steel is used, is the member adequate for a total load of 100 kips?
Solve: Select the lightest 28 ft long W12 available to support a factored tensile load of Pu = 400 k. Assume there are 2 lines, (lines are 5” apart) of 7/8" bolts in each flange (4 lines total) and 3 bolts per line @ 4” o.c. and 4” to end. Assume A992 steel. Dimensions are from centers of bolt holes.
Select a 9-m long W10 section of A572 Grade 50 steel to support a tensile load of PD = 490 kN and PL = 580 kN. The member is assumed to have one line of holes in each flange and two lines of holes in the web for 19 mm diameter bolts. There will be four bolts in each line 100 mm on center. Neglect block shear