Select a W16 shape of A36 steel for acolumn that must resist a service deadSectionAgW16x8926.4load of 140kips and a live load of 150kips.The effective length is 20ft. Use ASD. Referto the AISC properties viewer for the otherdata needed for the computation.W16x7722.9W16x6720

The question is based on the A36 steel column. The effective length of the column, dead load, and…

Answered: Select a W16 shape of A36 steel for a…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Similar questions

I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
Plz do not use gpt if u use chatgpt i will downvote you again don't use chatgpt
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
A76 x 76 x6 mm angular section shown is welded to an 8 mm thick gusset plate. The length L1 is 65 mm, L2 is 125 mm, and the cross sectional area of the angle is 929 sq.mm. Fy-248MPA and Fu -400MPA. Gusset Plate Alowable Sresse Alowable tensle stress igross ara)0.00 Alowable tereile stres net area)0SOF. Allowable shear stress (net ares)0.30F. Determine the value of P based on net area using a strength reduction coefficient of 85% O 138.24 KN O 140.14 kN O 157.93 kN O 304.00 N Next
7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is structural tubing however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? The section is 8" x 8" x 7.94 mm thick: Use Fy=248 MPa: E=200,000 MPa AISC wall thickness Ix 106 S x 103 Jx 103 mm4 mm3 mm4 rx =ry Area Ag (mm2) mm Designation Weight/m 8x8 7.94 47.36 6,039 79.25 37.84 371.99 60.35 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narative form to support your cho'ce) 8x8 14.29 80.61 10,258 76.2 59.52 585.02 99.06 8x8 72.7 9,290 76.96 54.53 539.13 90.32 8x8 9.53 56.09 7,161 78.48 44.12 432.62 70.76 mm 12.7 Zx 103 mm3 437.53 714.48 650.57 512.92
أ.د. رمضان المبروك A PL170mm x 10mm tension member is welded to a gusset plate as shown in Figure below. The steel is A36. Assume that Ae = Ag and compute the following. %3D fy = 250 MPa & f, = 400 MPa %3D %3D PL 170mmx10mm a. The design strength for LRFD. . The allowable strength for ASD. roblem (4):
3. Determine the maximum tensile capacity of a L 178 x 102 x 19 angle as shown below if bolt diameter = 24 mm. The long leg of the member is connected to a 24mm thick guest plate. Use A572M gr.345 steel material. Ta 76 → 76 V L178x102x19 mam 76 76 5 38 4. The tension member shown below is a C 310 x 30.8 of A572M gr 345 steel materials. Will it safely support a service dead load of 265 kN and a service live load of 555 kN.
A For the truss shown, find veyticat deflection bylunit lead Methed. EA 15 _atfd) Ioku for all members increase in temp is (50€) in (ad) short in (ad)is (3 Emfr
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
EQuiz No.3 584nkkz1 Cc7KLzOsdr9YUFgvcfFSqpsdlyljtewQ/formResponse Choose the correct answer What will be the value of load applied parallel to the diagonal of (100x100x100))mm cube since the splitting tensile strength=3 Mpa 57.8 KN O 46.7 KN O 47.1 KN O (28)=27.5 Mpa, then the fc(180)=-- for concrete produced using moist
pon 9.18 A steel rodin. in diameter and 25 ft long is subjected to an ace axial tensile load of 15,000 lb. Compute (a) stress ons Lanogsib & new (b) strain (c) total elongation aaste sviesiqmos srit nimmst gaites 900 viss srit .rwoda al

SEE MORE QUESTIONS

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Solid Waste Engineering

Civil Engineering

ISBN:

9781305635203

Author:

Worrell, William A.

Publisher:

Cengage Learning,

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Solid Waste Engineering

Civil Engineering

ISBN:

9781305635203

Author:

Worrell, William A.

Publisher:

Cengage Learning,

SEE MORE TEXTBOOKS

Select a W16 shape of A36 steel for a column that must resist a service dead load of 140kips and a live load of 150kips. The effective length is 20ft. Use ASD. Refer to the AISC properties viewer for the other data needed for the computation.