SETB: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 18 mm, is subjected to internal pressure of 3 MPa. (a) Show that the steel cylinder is thin-walled (b) Calculate the tangential and longitudinal stresses in the steel.(c) To what value may the internal pressure be increased if the stress in the steel is limited to 100 MPa?

SETB: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 18 mm, is subjected to internal pressure of 3 MPa. (a) Show that the steel cylinder is thin-walled (b) Calculate the tangential and longitudinal stresses in the steel.(c) To what value may the internal pressure be increased if the stress in the steel is limited to 100 MPa?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.7P: (a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the...

See similar textbooks

Similar questions

(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
A cylindrical steel pressure vessel 60 cm in diameter with a wall thickness of 30 mun, is subjected to an internal pressure of 6 Nmm. (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 200 MN/m?
Find the maximum value of P that will not exceed a stress in steel of 113 MPa, in aluminum of 91 000 KPa, or in bronze of 110 MPa if the aluminum rod is rigidly attached between a steel rod and a bronze rod.
A steel rod bolt 8mm diameter inside fits loosely on an aluminium tube and 16mm outside diameter. A nut is fitted into the bolt and tighten against the tube, until the stress in the bolt is 40N/mm². Calculate the stress in the tube. If the temperature of the assembly is now increased by 100°C. What will be the new stress in each component?
A cylinder head of a steam engine is held on by 14 bolts. The effective diameter of the cylinder is 35 cm and the steam pressure is 8.5 kg/cm2. Assuming that the bolts are not initially stressed, find the diameter of each of the bolts if the tensile stress is not to exceed 200 kg/cm2.
A cylinder head of a steam engine is held on by 14bolts. The effective diameter of the cylinder is 35cm and the steam pressure is 85N/mm².Assuming that the bolts are not initially stressed; find the size of bolts if the tensile stress is not to exceed 20N/mm²
With a thick walled cyclinder the inner radius is 0.05m and out radius is 0.2m. The internal pressure is 200 MPa - What is the hoop and radial stress at the inner surface? - What would be a suitaable material for the cyclinder under von mises criterion?
SHOW ILLUSTRATION AND SOLUTION Problem 2: Steel railroad rails 10 m long are laid with a clearance of 3 mm at atemperature of 15 oC. E = 200 GPa and  = 11.7 x 10 - 6/oC. 1. At what temperature will the rails just touch?2. What stress would be induced in the rails at that temperature if there were no initial clearance?
A tube from aluminium with an outside diameter of 50 (mm) and a wall thickness of 5 (mm) is used as a compression member. If the axial normal stress in the member must be limited to 90 MPa, what is the maximum force (in kN) that the member can support.