shaft of 53 mm diameter is subjected to a bending moment of 1477158 N-mm and a torque T N-mm. If the yield point of the steel in tension is 322 Mpa, find the maximum value of this torque without causing yielding of the shaft according to maximum

shaft of 53 mm diameter is subjected to a bending moment of 1477158 N-mm and a torque T N-mm. If the yield point of the steel in tension is 322 Mpa, find the maximum value of this torque without causing yielding of the shaft according to maximum

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.1P: A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends....

See similar textbooks

Related questions

Q: Determine the coordinates of the centroid of the area that lies tween ne straight line x =2y/3 and…

Q: If D rotates with angular vlocity of 7 rad/s clocwise increasing with constate rate of 100rad/s^2,…

Q: A U-tube manometer contains a liquid having a 3 density of 800 kg/m. When the manometer is connected…

Q: A U-tube manometer contains a liquid having a density of 800 kg/m. When the manometer is 3 connected…

Q: 20kN/m 20kN/m 1m 2m 1m 1m 5m

A: Given: Total length of a cantilever beam, l =5 m Beam is subjected to two uniformly distributed…

Q: Given the image below, AB and BC are joined by a hinge in b. End A of member ASB is pin supported…

Q: Hello, there is frost on the evaporator in the air conditioner. How to optimally calculate the gap…

A: INTRODUCTION : The evaporator is used to absorb heat from the high-temperature space in order to…

Q: A screw jack mechanism is to be incorporated into the machine as part of a levelling system. The…

A: Given Pitch, P = 6 mm Mass, m = 500 kg Coefficient of…

Q: Note: Remember to round off the final answer to three significant figures. Example 2: Convert the…

Q: List down the formulas for calculating the shear stress and angle of twist of the following cross…

A: It is asked to write the shear stress and angle of twist formula for the cross-sections of shape…

Q: Q2/ Determine the forces at the pin joint (F) and the roller support (G) ? 30KN 20 KN 2m BY 2m D 2m…

Q: Co

A: Let RA and RB be the reactions at the support A and B respectively. Apply +↺∑Mat A= 0 in the above…

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

A: Answer: Option (C): T = 7646 N, FBx = 3823 N , FBy = 4169 N

Q: Exercise about rotating blocks

A: A block can be rotated about one of its edge if there are certain friction between the block and and…

Q: Draw the shear and moment diagrams for each beam shown in figure:

A: Draw the free-body diagram of the beam.

Q: ky = 4.9 kN/m I. Determine the magnitude of force acting on the beam from spring A. il. Determine…

Q: 3- Discuss the siphon process and what benefit of it?

A: Question 3 Siphon process and it's benefits

Q: 10N 1m 1 m 1 m 1m c 1 m 5N 1 m E 10N + 10N 1 m 1 m 20N 5N 10N Find the summation of torque / moments…

A: clockwise moment is taken as +ve Moment at B, Mb =(5*3)+(10*2)+(10*1)+(20/2)-(10*1)-(5*2)-(10*2) =…

Q: To mixer design, estimate the power requirement (kw/m³), agitation type for homogenous reaction…

A: A shaft is a rotating machine element generally circular in cross-section which supports…

Q: At the instant shown, end A moves upwards with a constant speed of 4.50 m/s. At the same time, the…

Q: the section. The permissible stresses are 10 N/m

A: given:

Q: A 3.19 kg/s of oxygen gas enters a compressor with the shown conditions and then enters the heat…

Q: Determine the change in exergy in kJ for each of the following processes in the system with 1 kg of…

A: given; mass of steam(m)=1kgtemperature(T1)=2400c…

Q: An uncontrolled 850 kg car strikes squarely a motorway crash cushion in which the car is brought to…

A: Given, Mass of the car = m = 850 kg Length of the crash cushion = L = 4.6 m Force required to crush…

Q: A crate of 64 kg simply stands on the moving cart with constant acceleration a. The height from the…

Q: 5-Draw the relationship between percent passing and sieve size. and discuss.

A: We will answer the first question since the exact one is not specified. Please resubmit the question…

Q: Q2/ Determine the forces at the pin joint (F) and the roller support (G) ? 30KN 20 KN 2m BY 2m D 2m…

Q: Q1. Determine Reactions at point A and tension in the cable BC for the following figure. 500 N 3 m 2…

Q: Example The bob of a 2-m pendulum describes an are of circle in a vertical plane. If the tension in…

Q: Determine the equation of motion in a matrix form using Newton's second law, [m]y+ [c]y + [k]y = F.…

Q: (a) R-410a, T=-25°C, v=0.05 m³/Kg, P=?, s=? (b) Ammonia, P=200 kPa, s= 6.21 KJ/Kg-K, T=?, v=? (c)…

A: Use required table for finding out the unknown values.

Q: 1- Select the optimum choice for: high speed air craft skins material. Table 1: The properties of…

A: The most extensively used aluminium alloy in aircraft development is 2024. The alloy is a…

Q: A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given Tensile modulus, E1 = 10 GPa E2 = 0.4 GPa Find Tensile…

Q: A crate of 68 kg simply stands on the moving cart with constant acceleration a. The height from the…

A: INTRODUCTION : In this problem, one body accelerates on an inclined plane against its own weight.…

Q: Numerical Exercise 1. A flat plate is supplied with a constant heat flux of 100 [W/m2] from bottom.…

Q: In the mechanism shown below, points E and B have the same vertical coordinate. Fir velocities of…

Q: A steel tire, 20 mm thick, 90 mm wide, and 1600.0 mm inside diameter is heated and shrunk onto a…

A: Answer: The torque required to twist the tire relative to the wheel is 113.1680 kN•m.

Q: Skydiver Luke jumps with his parachute of diameter D = 12m out of an airplane. The combined mass of…

A: Given : m=100 kg D=12 m Cd = 1.4 To find : Time taken to fall between 3000 m to 2000 m

Q: which type ot gears have point contact between two mating gears? olect the coect answer * Helical…

A: These questions are based on the concept of gears.

Q: 5. A 5kg ball is moving along a frictionless elliptical rod from B to A. one end of the spring is…

A: Soln Mass of ball = 5 kg System is frictionless ( energy conservation) At A & B Total energy at…

Q: Q1 : A rod made of carbon reinforced epoxy has a diameter 2.5 cm, length 1.25 m, and mass 0.95 kg.…

Q: Example 2: Convert the quantities 300 lb.s and 52 slug/ft to appropriate SI units.

Q: Draw the shear and moment diagrams for each beam shown in figure:

Q: A U-tube manometer contains a liquid having a 3 density of 800 kg/m. When the manometer is connected…

Q: Compute the mechanical efficiency of a motor with an overall efficiency of 85% and a volumetric…

A: To find mechanical efficiency of a motor

Q: A jet of water with a diameter of 52 mm (d) hits a set of vanes, the absolute velocities are as…

Q: Q2: Determine theX- and y-coordinates of the centroid of the shaded area. 20mm bomm

Q: OA = 20 cm, AB =30 cm, BM=12 cm Crank OA rotation law o(t) = (t/3)° (angle o radian, time t seconds)…

Q: The two disks A and B have a mass of 3 kg and 5 kg, respectively. If they collide with the initial…

A: Given Data Mass of A (mA) = 3 Kg Mass of B (mB) = 5 Kg e= 0.65

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A mild steel shaft of 53 mm diameter is subjected to a bending moment of 1477158 N-mm and a torque T N-mm. If the yield point of the steel in tension is 322 Mpa, find the maximum value of this torque without causing yielding of the shaft according to maximum shear stress

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
A circular steel tube of length L = 1.0 m is loaded in torsion by torques T (see figure). (a) If the inner radius of the tube is r1= 45 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1(in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maxi mum permissible outer radius (r2)max?
A copper tube with circular cross section has length L = 1.25 m, thickness t = 2 mm, and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 300 N·m torque acting at the ends. If the allowable shear stress is 25 MPa and the allowable angle of twist between the ends is 2.5°, what is the minimum required outer diameter d?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?