Shapes Shown Below, Using Scale (1:1) 13 38 $25

Q: answer all parts

A:

Q: Give the table mentioning AQI Values, Descriptors and Colors used?

A: The Air quality Index is often abbreviated as AQI. The government has prescribed some set of values…

Q: Calculate the square footage of the following rooms. (Show all necessary calculations, including…

A: The total area of the kitchen(AT) = Area of rectangle + Area of trapeziumAT = (13×20) +…

Q: Define The required diameter

A: A diameter is a chord that runs through centre point of circle. The centre of circle is at midpoint…

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: ****************** Draw a flowchart to find the sum for the following numbers: Sum= 6 + 10+ 14 + 0

A:

Q: Define Peclet number.

A: It is defined as the ratio of the rate of advection of a physical quantity by the flow to the rate…

Q: 2. Complete the profile level notes shown below, perform the customary arithmetic check, provide a…

A: Solution: The table is below:

Q: HELLO PLEASE HELP, WITH COMPLETE SOLUTION. PLEASE DO NOT MAKE IT COMPLICATED THANK YOUU! 4 DECIMAL…

A:

Q: missing value

A:

Q: Some of the numbers on this illustration of a cross-section of a typical Gothic cathedral correspond…

A: Given- The cross-section of a typical Gothic cathedral is given. It is needed to identify a few…

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: Enlarges or reduces selected objects, keeping the proportions of the object. explode command…

A: Answer - Scale command Explanation- Enlarges or reduces selected objects, keeping the proportions…

Q: True or false Topic: Quantity surveying 1. wherever possible, estimators should use prices based on…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Suppose a problem tells you that the length of a gate is drawn to scale. The scale of the drawing is…

A: given scale of drawing=1:50 length of gate on paper =10cm we know that  scale of drawing=(dimension…

Q: A scale of a plan is 1:200.The distance between two points x and y on the plan measures 435mm.…

A:

Q: (C): Find representative Fraction scale (R.F) from verbal statement of (6 inch to 1 mile) (12mile to…

A:

Q: express each measurement in feet.42 inches

A: Given: The measurement is 42 in.

Q: dimension is 23.6 cm. What is the actual dimension?

A:

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: If the actual dimension is 46 m and the scaled dimension is 184 cm, what is the scale used?

A:

Q: Complete the table below.

A:

Q: Enumerate at least five different units of measurement that usually use at hom

A: There are many ways in which technology can help in this case. If you want to wake up early in the…

Q: Print scale 1:50 means that The draft is 50 times less expensive than the original A 3 cm…

A: A 3cm corresponds to half a meter

Q: You are trying to plot a drawing using the 1:100 scale, but the drawing will not fit to the plot…

A: The ratio of distance on map to its distance on ground is known as scale. y

Q: This assignment consists of determining the quantities for a cost estimate in different units.…

A: from the given data from the problem Type  Length height Area After completion of deduction…

Q: How many studs are require for the exterior wall on the main floor if there are two doors and 6…

A: Hi! Thank you for the question As per the honor code, We’ll answer the second and third question…

Q: (a) With a neat sketch write short notes on mechanically operated trucks to move material from one…

A: Solution: a.  The Mechanically operated trucks that are used to carry material from one location to…

Q: value. Deformed Undeformed 16.6 0.24 mm

A: To find strain in x and y direction and shear strain

Q: Draw the following for the following figure (complete front section / horizontăl projęctión / side…

A:

Q: Calculate the second moment of area for a 50 mm ×100 mm stud with the actual dimensions shown on…

A: Given:- The dimension of the stud = 50 mm × 100 mm  The actual dimension of the stud = 45 mm × 105…

Q: 1. What thickness limit classifies metal as being sheet? 2 What is the decimal size of 14 AWG sheet?…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: A sheet of paper for a poster is to be 18 ft2 in area. The margins at the top and bottom are to be 9…

A: Dimensions of the sheet to maximize the printed area:

Q: Directions: You are an architect in a constructiorn company. You are tasked to build 3 circular…

A: As mention above the the diameter and length of three circular tank are or we can say that capacity…

Q: Define People ware, Software, and hardware and its relationship to CAD

A: Peopleware represents one of the 3 core component of computer technology other 2 are software and…

Q: 3. Given below is the technical description of Lot 2081, Cebu Cadastre. N Show your complete…

A:

Q: Construct a diagonal scale and show on it a distance of 1.12 inche

A: Diagonal scale is an engineering measuring instrument that is combined with a set of parallel…

Q: Fill up tabele#1 below to calculate exact quantity of cach given item as given in figure#1 & #2…

A: Calculate the total centerline length L as given as, L=4.3-0.125+6.5-0.125+5=15.55 m 1) Item…

Q: Draw the figure/illustration. Show complete solutions

A: a.) Calculate the initial velocity Vi=VC2+HC2Vi=122+202Vi=23.32m/s Therefore the initial velocity is…

Q: A plan drawn to a scale of 1:3000 was measured by mistake by a scale of 1:4000. The percentage error…

A:

Q: Complete the profile level notes shown below, perform the customary arithmetic check, provide a…

A: Solution: The table is formed as:

Q: Draw a scale bar for 1:800 and specify the measurements.

A: 1:800 means 1 m on paper means 800 m on field.

Q: determine the following:

A:

Q: A contractor is to place tiles for a living room with a floor area of 8 meters x 6 meters. If each…

A: Total floor area, A=8 x 6=48m2 tiles dimension, a= 0.4 x 0.4=0.16m2

Q: 8. Various activities of a project, are shown on bar charts by A. crosses C. dots and dashes B.…

A:

Q: Calculate the number of division of the main scale that is equal to the 8 divisions of the extended…

A: Given data- 8 divisions of the extended vernierTo Find-The number of divisions of main scale.

Q: express each measurement in feet.60 inches

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.