Show that the points A, B and C, with position vectors p+q, p-q and p respectively, lie on the same straight line.

Q: 6) The number of degrees of freedom of a planar linkage with 8 links and 9 simple revolute joints is

A: Given:number of links, l=8number of joints, j=9

Q: What type of axle housing resembles a banjo?

A: Given Data : Banjo

Q: A mass of 7 kg undergoes a process during which velocity decreases from 32 m/s to 19m/s, while the e...

A: Givenm=7kgv1=32m/sv2=19m/su1=1.24kJ/kgu2=2.08kJ/kgQ1=2kJQ2=-0.8kJ

Q: Air with cv = 0.723 KJ/Kgm - °R is compressed in a piston-cylinder machine according to pV1.3 = c fr...

A:

Q: 10. Atmospheric pressure, Stau 11. Atmospheric pressure, stated in psig, is 12. Atmospheric pressure...

A: 10. 14.7 psi 11. 0 psi (14.7-14.7) 12. 29.9212 in Hg 13. above and below 14. inversely as long as th...

Q: In a certain diesel- electric power plant, diesel generator set has the following data: Diesel fuel...

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for y...

Q: resultant unbalance force on the rotor is

A: Given; A balanced rigid disc mounted on a rigid rotor has four identicalpoint masses.Each can carry ...

Q: The current in a component is reduced uniformly from 100mA to 20mA over a period of 8.0s.What is the...

A: Given:I1=100 mAI2=20 mAt=8 sec

Q: esigned ambient conditions are 15° C and 1 bar and compressor has to be a part of stationary power ...

A:

Q: 3. WHAT TURBINE WORK AND ENGINE EFFICIENCY IF THE INLET PRESSURE AND TEMPERATURE ARE 24MPA AND 510°C...

A:

Q: PROBLEM 2 This force-couple system is to be replaced by an equivalent system consisting of the follo...

A:

Q: 12) The lengths of links of a 4-bar linkage with revolute pairs only are p, q, r and s units. Given ...

A:

Q: 1- The steady state temperature profile for a wire carrying current is R* (1- G) gR T(4) = + + T; %|...

A:

Q: An aluminum cube with an edge of 5 cm is resting on the ground on one of its faces. calculate the pr...

A: Given data  s= 5 cm = 0.05 m  d= 2700 kg/m³  Note: diagram is not necessary for the understanding th...

Q: ) Neglecting the weight of the beam, compute the reaction at the ends as shown in Fig 2 kN Q KNm

A:

Q: In a pipe with constant flow rate, if diameter of pipe is halved and length of pipe is doubled, then...

A:

Q: For the same system, write equations of motion in the matrix form: ku k12 :) m12 ) = 0 m11 m21 m22 k...

A: Given: →m11m12m21m22x¨y¨+k11k12k21k22xy=0→m11x¨+m12y¨m21x¨+m22y¨+k11x+k12yk21x+k22y=0so→m11x¨+m12y¨+...

Q: A simple beam AB of length L supports aconcentrated load P at the midpoint (see gure).(a) Evaluate ...

A: Given data as per question The load applied =P Calculations ∑Fx=0HA=0∑Fy=0RA+RB=P   −−(1)∑H=0RB×1=P×...

Q: A centrifugal pump works against 10 m at 1000 rpm. varies are curved back at an angle of 30° to the ...

A:

Q: Where does the value of the Rin the solution came from?

A:

Q: Drive Shaft Outlet Blades Inlet Scroll Impeller

A: IMPELLER FAN A fan impeller is ordinarily joined to the turning shaft. Outer rotor engines basically...

Q: A strip of thickness 40 mm is to be rolled to a thickness 20 mm using a two-high mill having a rolls...

A: Given:h1=40 mmh2=20 mmd=200 mm

Q: A crank of radius 12cm is rotating at 60rpm with an angular acceleration of 50 rad/. The tangential ...

A: Given: Crank radius= 12 cm= 0.12 m angular acceleration= 50 rad/s2 To determine: Tangential accelera...

Q: Explain the different approaches in doing research

A: given; explain different approaches in  doing research.

Q: You answer should include these 5 aspect (Brief answer ) 1- what is striling engine ? 2- General his...

A: A Stirling engine is basically a mechanical device that converts temperature difference directly int...

Q: As a process engineer, you are required to deposit conformal silicon thin films with 500 nm thicknes...

A:    The vaporisation of a material occurs when it is heated to a temperature where the vapour pressur...

Q: 3 kN/m. EN. A Ay Draw 6 m zm. S.F. 9 B.M.5 shear force and bending moment diagram

A:

Q: Construct a view that will show both triangles in edge view.

A: Solution: The edge view of both the triangles is shown below:

Q: Determine the force in members CD ( in kN)of the Pratt truss. State if the members are in tension or...

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN MEMBER CD

Q: A fixed-end beam is subjected to a pointload at mid-span. The beam has a rectangular crosssection (a...

A: given; →P=12KN    =12*103N→L=4m   =4*103mm→hb=2→E=11GPa   =11*103MPa (a)maximum deflection(δmax)=2mm

Q: Determine the internal resultants FG, VG, and MG on the cross-section at G of the horizontal frame m...

A:

Q: What is the dimensioning system shown in the figure below A. Alligned dimensioning system B. undirec...

A: option (B) unidirectional dimensioning system

Q: A single-degree-of-freedom oscillator is subjected to harmonic excitation F(t) = F, cos(ot) %3D as s...

A:

Q: 12) The lengths of links of a 4-bar linkage with revolute pairs only are p, q, r and s units. Given ...

A:

Q: When a hydrocarbon fuel is burned, almost all of the carbon in the fuel burns completely to form CO2...

A: 0.59 kg of CO2 is produced for each kWh of electricity generated from a power plant that burns natur...

Q: 8) A five-link planar mechanism with five revolute pairs (one link is fixed). The number of degrees ...

A:

Q: A Pelton wheel develops 1800 kW under a head of 120 m while running at 210 rpm and discharging of 2....

A:

Q: a. You have a rock with a volume of 15cm³ and a mass of 65 g. What is its density? b. You have a dif...

A: Given data,  a) m= 65 g , V= 15 cm³  b) m= 60 g and V = 35 cm³

Q: Show how buoyancy equations are derived for floating and submerged bodies

A: Buoyancy of a body is related to the amount of fluid displaced by it and its weight. Archimedes' pri...

Q: , hinged at A and D and pinned at B and C as sho a. Determine the value of P that will prevent motio...

A:

Q: teel wire 5u-m long hanging vertically supports a weight of 1200 N. Determine the required wire diam...

A: Given;-δ=PLAE4x10-3=1200x5π4xd2x200x1094x10-3=1200x5x4πxd2x200x109d2=1200x5x4πxd2x200x109x4x10-3d=3....

Q: A crate is supported by a cable and spring. The spring has unstreached length of 2m. Calculate stiff...

A: Given:m=40 KgL=2 m

Q: Write short notes on: (i) Gear pump (ii) Lobe pump (iii) Screw pump

A:

Q: Required: i. Change in length if the rod is heated to 200°C. ii. Change in diameter if T; = 200°C. i...

A:

Q: A in.x 3 in. bar of 1045 hot-rolled steel is loaded by a tension force varying continuously from Pma...

A:

Q: A propped cantilever steel beam is constructedfrom a W12 x 35 section. The beam isloaded by its self...

A: Given data as per question Length of the beam =11.5 ft  E = 30,000 ksi. For   W12 x 35 section  q = ...

Q: We want to predict the drag force on a remote-control airplane as it flies through air having a dens...

A: Solution: Given Data: ρa=1.21 kg/m3μa=1.76×10-5 Pa-sVp=32 m/sD=75 mmρw=3 kg/m3μw=1.82×10-5 Pa-s   No...

Q: What are the important step in sample preparation for material characteriztion?Just basic idea neede...

A: Introduction: material characterization: It is the analysis of the morphology, composition and the s...

Q: P2

A: A plasma-upgraded substance fume affidavit reactor has been created to combination evenly adjusted c...

Q: A strain gage is installed in the longitudinal direction on the surfaces of an aluminium beverage ca...

A: