SHOW UNIT CANELLATION AS WELL AS STEP BY STEP SOLUTION. ANSWERS MUST BE IN 4 DECIMAL PLACES INCLUDING YOUR FINAL ANSWER. A 10 m diameter cylindrical tank has a height of 5 m and is full of water at 20°C. (Unit weight= 9,879 kN/m³) If the water is heated to a temperature of 50°C (Unit weight= 9.689 KN/m³), solve for. a. The weight of the water at its initial temperature in kgr b. The volume of the water when heated to its final temperature in cm³ c. The volume of water that will spill over the edge of the tank in cm³.

SHOW UNIT CANELLATION AS WELL AS STEP BY STEP SOLUTION. ANSWERS MUST BE IN 4 DECIMAL PLACES INCLUDING YOUR FINAL ANSWER. A 10 m diameter cylindrical tank has a height of 5 m and is full of water at 20°C. (Unit weight= 9,879 kN/m³) If the water is heated to a temperature of 50°C (Unit weight= 9.689 KN/m³), solve for. a. The weight of the water at its initial temperature in kgr b. The volume of the water when heated to its final temperature in cm³ c. The volume of water that will spill over the edge of the tank in cm³.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 24P

See similar textbooks

Similar questions

Please show the complete solution. (Example: Conversion of Units) A rigid container is closed at one end and measures 8 in diameter by 12 in long. The container is held vertical and is slowly moved downward until the pressure in the container is 17 psia. What will be the depth of the top of the container from the free water surface?
Figure 7 shows a pump partially submerged in oil (sg=0.90) and supported by springs. If the total weight of the pump is 14.6 lb and the submerged volume is 40 in3 , calculate the supporting force exerted by the springs.
Show complete solutions and figures. The shown tank with an attached manometer contains water unit weight is 9.79 kN/cu.m.at 200oC. The atmospheric pressure is 100kPa. There is a valve located 1m from the surface of the water in the manometer. The valve is closed trapping the air in the manometer, and the water is added to the tank to the level of the valve. Find the increase in the elevation of the water in the manometer assuming the air in the manometer is compressed isothermally. a) 101.3mm b) 92.7mm c) 73.2mm d) 82.4mm e) None
As shown in the figure, determine the gage pressure on the bottom of the tank in kPa. Considering the total gage pressure at the bottom of the tank what will be the absolute pressure if the barometric pressure if 725 torr?
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference Pfresh water- Psea water= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
A vertical cylindrical tank is 9 m high and 5 m in diameter. It is two thirds full of water and is rotated uniformly about its axis at a speed of 48 rpm. what is the pressure at the center bottom of the tank? Unit of the Correct Answer: kPa Decimal Places required in the final answer: 3 DECIMALS PLS
Determine the magnitude and point of application of the horizontal and vertical compenents of the hydrostatic pressure force acting on the prismatic surface a b c d e. The surface lenght (dimension perpendicular to the figure) is 4.5 m. The unit weight of water =9.81 Kn/m3
Assuming the tank is starting from full, develop an equation to determine the height ofwater in the tank as a function of time, h(t), if the inlet valve is closed and the outlet valve is opened.Determine the time required to empty the tank. (hint: use mass balance and Bernoulli’s; think about whatwould change and what would remain constant)
A horizontal pipe carries cooling water from a reservoir as shown in the following figure. If the pipe diameter is 20 cm, the flow rate is 0.06 m3/s, what is the pressure at L= 2000 m? Calculate head loss as hL = 0.015(L/D)(V 2/2g)
From the given figure. From the e-log p plot, two points were given. p1 = 80 kPa e1 = 0.60 p2 = 150 kPa e2 = 0.40 Determine the Liquid Limit.
The system shown in the figure is used to accurately measure the pressure changes when the pressure is increased by ΔP in the water pipe. When Δh = 90 mm, what is the change in the pipe pressure?
Determine the pressure required to reduce the given volume of water by 1 % (Bulk modulus or water=2x108 N/m2)