Given the vibrating system below: K4 Y(t) =Ysin30t where for = 30 and Y=20mm Find the following: K3 K1 K2 m C3 ㅏㅏ C2 C1 C5 C4 M = 10 kg K1=100 N/m K2= 80 N/m K3=75 N/m K4= 120 N/m C1 = 20Ns/m C2=40 Ns/m C3= 35Ns/m C4=15 Ns/m C5=10 Ns/m 1. Type of Damping 2. Equation of motion x(t). Assume Initial conditions for displacement and velocity. 3. Graph 2 cycles of the vibrating system. You can use third party app for this.

Given the vibrating system below: K4 Y(t) =Ysin30t where for = 30 and Y=20mm Find the following: K3 K1 K2 m C3 ㅏㅏ C2 C1 C5 C4 M = 10 kg K1=100 N/m K2= 80 N/m K3=75 N/m K4= 120 N/m C1 = 20Ns/m C2=40 Ns/m C3= 35Ns/m C4=15 Ns/m C5=10 Ns/m 1. Type of Damping 2. Equation of motion x(t). Assume Initial conditions for displacement and velocity. 3. Graph 2 cycles of the vibrating system. You can use third party app for this.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

subject: Statics of Rigid Bodiesshow your solution i will rate if solved quickly
Please answer the following question A cigarettes dispenser requires a south African five-rand (R5) coin with a mass of 9.5 g to dispense one cigarette with a mass of 0.2 g. The design of such a cigarette dispenser is based on a helical spring, of negligible mass, which is found to extend 0.1 mm under a mass of 0.2 g. The spring can support a total mass of a coin. As the customer place money on the dispenser, the spring and coin system displace vertically through 4 mm and release. 1.1. Provide a schematic representation of the mass and spring system. 1.2. Calculate the frequency of natural vibration of the dispenser. 1.3. Determine the velocity of the coin when it is 2 mm below its resting position.
Statics of rigid bodies *Solve the following problems completely: Show your complete solution and drawing:
Statics of rigid bodies I. Solve the following problems completely: Show your complete solution:
Static of Rigid Bodies. Step by step solution. Thank You.
II. Provide complete solutions per problem. No need to copy the problem butprovide the ff format: (a) given (b) required (c)solution 1. A journal of basic size of 75 mm rotates in a bearing. The tolerance for both the shaftand bearing is 0.075 mm and the required allowance is 0.10 mm. Find the dimensions ofthe shaft and the bearing bore. 2. A medium force fit on a 75 mm shaft requires a hole tolerance and shaft tolerance eachequal to 0.225 mm and average interference of 0.0375 mm. Find the hole and shaftdimensions.
Statics and rigid bodies: Please Show me how to solve the following practice problem. In step by step solution ( Thank you! :) )
A punching machine requires 1600 ft-lb of energy to punch a certain hole. During the punching operation, the speed of the machine is reduced from 180 rpm to 160 rpm. The weight of the arms and hub is considered to be 10 % of the rim weight, and the mean diameter of the flywheel is 32 inches. a) What is the mean or operating rpm of the flywheel? b) Find the coefficient of fluctuation. c) What is the maximum speed of the flywheel, in fps? d) What is the minimum speed of the rim, in fps? d) Determine the weight of the rim, in lb. e) What is the weight of the flywheel, in lb? f) Determine the weight of the arms and hub, in lb.
Generally, final design results are rounded to or fixed to three digits because the given data cannot justify a greater display. In addition, prefixes should be selected so as to limit number strings to no more than four digits to the left of the decimal point. Using these rules, as well as those for the choice of prefixes, solve for σ. σ = M/Z, where M = 1 770 lbf-in and Z = 0.934 in³. (type the value and the unit ex. 1.00psi)
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) the diameter of reference circle, d2=( )mm the diameter of addendum circle da2 =( )mm the diameter of dedendum circle df2 =( )mm
Subject:statics of rigid bodiesshow your solution please
Subject: Statics of Rigid Bodiesshow your solution please