shows a cylinder made of two different materials with elastic modulus of E, and Ez, and uniform cross section area, A. The cylinder is subjected to forces F and P, and fixed support at one end. If the cylinder is modelled as a spring system to represent one-dimensional bar element in finite element method, i. sketch the spring system for the cylinder and derive the equilibrium equations, ii. express the equations (i) in finite element matrix formulation. E1 E2 Li A cylinder subjected to two forces

shows a cylinder made of two different materials with elastic modulus of E, and Ez, and uniform cross section area, A. The cylinder is subjected to forces F and P, and fixed support at one end. If the cylinder is modelled as a spring system to represent one-dimensional bar element in finite element method, i. sketch the spring system for the cylinder and derive the equilibrium equations, ii. express the equations (i) in finite element matrix formulation. E1 E2 Li A cylinder subjected to two forces

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.1P: A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
a helical compression spring with squared and ground ends is ti be made of a steel wire 79 gpa and presetting is to be used. the operation load of the spring can be considered static. If the maximum working force is 292 N and a force of 35 N is required when the spring is 30 mm longer, determine the spring constant k
A length of 18 mm diameter steel wire is coiled to a close helical spring having 9 coils of 72 mm mean diameter, and the spring has a stiffness k. If the same length of wire is coiled to 9 coilsof 54 mm mean diameter, then the spring suffness will be
I need the derivation with neat and complete explanation.don't do if you are not aware. Derive the maximum shear stress induced, in the wire of a closed-coiled helical spring which can an axial load W. Assume mean radius of spring coil is R and diameter of spring wire is d.
A close coiled helical spring that is made of a material with a shear modulus of 150 GPa, has a wire diameter of 10 mm, a solid length of 100 mm, and a stiffness of the spring is 15 kN/m. Calculate:(i) The mean diameter of the coils ,(ii) The shear stress induced in the spring wire for an axial deflection of 35 mm, and(iii) The work done extending the spring by 25 mm
A helical spring in which the mean diameter of the coil is 8 times the wire diameter is to be designed to absorb 0.2 kNm of energy with an extension of 100 mm. The maximum shear stress is not to exceed 125 N/mm2. Determine the mean diameter of the spring, diameter of the wire and thenumber of turns. Also find the load with which an extension of 40mm could be produced in the spring. Assume G = 84 kN/mm2.
A 200 kg load is hung on a wire of length 4 m, cross sectional area of 0.2 x 10 -4 m2 and Young’s modulus of 8 x 1010 Pa. What is its increase in length?
A vertical close-coiled helical compression spring must have a stiffness of 900 N/m under a load of 45 N and the maximum shear stress induced due to this load is to be 120 MPa. With the spring fully compressed the vertical height over the coils is 45 mm. Calculate (a) the wire diameter; (b) the mean coil diameter; and (c) the number of coils (G = 40 GPa)
Find the equivalent spring constant of a uniform mild steel rod length of 2.5 m, cross-sectional area of 100 cm2 and Young's modulus of 210 GPa subjected to an axial tensile (or compressive) force F= 500 N.
An 18 coils helical spring having a load of 100kg. The modulus of elasticity in shear of spring is 96.62 GPa, OD of 9.256 cm and with wire diameter of 9.525 mm. The spring is squared and ground ends. Compute for the following respectively : 1) number of effective coils 2) spring index 3) axial load 4) deflection (mm)
A helical compression spring subjected to compressive load. The maximum shear stress induced in the cross-section of the wire is 24 MPa. For the same compressive load, if both the wire diameter and the mean coil diameter are doubled, calculate the maximum shear stress induced in the cross-section of the wire?
A helical spring is made of 10 m diameter steel wire wound on a 100 mm diameter mandrel. If there are 10 active coils what is spring constant Take: C= 100 GPA What force must be applied to the spring to elongate it by 50 mm?