A uniform horizontal beam with a length of 12.00 m and a weight of 500 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of 60.0° with the horizontal. If a crate of (W)_N hanged 2.00 m from the wall, find the tension in the cable, as well as the magnitude and direction of the resultant force exerted by the wall on the beam. (Draw neat free body diagram) Use your last THREE digits of your ID for the missing weight (W) of the crate.

A uniform horizontal beam with a length of 12.00 m and a weight of 500 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of 60.0° with the horizontal. If a crate of (W)_N hanged 2.00 m from the wall, find the tension in the cable, as well as the magnitude and direction of the resultant force exerted by the wall on the beam. (Draw neat free body diagram) Use your last THREE digits of your ID for the missing weight (W) of the crate.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Similar questions

The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
Find the internal force system acting on section 3 for the pin-connected frame.
Find the magnitude of the pin reaction at B caused by the weight W=80lb. Neglect the weights of the members.
For the ladder in Prob. 6.17, find the internal force system acting on section 2, assuming that x < a/2.
Compute the tension TAE in Sample Problem 5.7 using one scalar equilibrium equation.
A uniform horizontal beam with a length of 1.7 m and a weight of 200 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of 35.0° with the horizontal. If a crate of mass (M) 87 kg hanged 1.7 m from the wall, find the tension in the cable, as well as the magnitude and direction of the resultant force exerted by the wall on the beam.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 2,2 kN. Angle α = 39 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N2 in the rod 2, considering that N2>0 for tension and N2<0 for compression.
A uniform horizontal beam 5.00 m long and weighing 350 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 50 with the horizontal. If a person weighing 550 N stands 1.50 m from the wall, find the magnitude of the tension T in the cable and the force R exerted by the wall on the beam.
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
nonuniform beam 4.50 m long and weighing 1.40 kNmakes an angle of 25.0° below the horizontal. It is held in position bya frictionless pivot at its upper right end and by a cable 3.00 m fartherdown the beam and perpendicular to it . The center ofgravity of the beam is 2.00 m down the beam from the pivot. Lightingequipment exerts a 5.00 kN downward force on the lower left end ofthe beam. Find the tension T in the cable and the horizontal and verticalcomponents of the force exerted on the beam by the pivot. Start bysketching a free-body diagram of the beam.
A 10-m uniform beam of weight 100 N is supported by two ropes at its ends. If a 400-N person sits at the center of the beam, what is the tension in the right rope?
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar