Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? (Non-anonymous questionO)

Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? (Non-anonymous questionO)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve.b. Plot the percent finer in a semi-log gradation chart.c. What is the maximum aggregate size of the sample?d. What is the nominal maximum aggregate size of the sample?e. What is the fineness modulus? Is it in typical range?
While measuring the abrasion value of sub-base aggregates category E sample was taken having dry weight of 10000 grams.Amount of fines passing through 1.7 mm sieve was 1550 grams. Workout the abrasion value of aggregates.
A sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results below. Determine the following: a. Percent passing through each sieve (Tabulation) b. Plot of the percent finer in the Semi-Log Gradation Chart c. Maximum Aggregate Size of the Sample (mm) d. Nominal Maximum Aggregate size of the sample e. Fineness Modulus
A sieve analysis test was performed on a sample of aggregate and produced the results shown in Table .Calculate the percent passing through each sieve. Plot the percent passingversus sieve size on:a. a semilog gradation chart, andb. a 0.45 gradation chart (Figure A.25).What is the maximum size? What is the nominal maximum size?
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket =14L Weight of empty bucket = 9.21kg Weight of bucket filled with dry rodded coarse aggregate: Trial 1 =34,75 kg Trial 2 =34.06 kg Trial 3 =35.74 kg a. Calculate the average dry-rodded unit weight b.If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.
A sieve analysis test was conducted for sample of fine aggregate and obtained theresults as shown in Table Q1. Calculate the percent passing of each sieve and classifythe fineness of fine aggregate based on fineness modulus analysis.
Sieve analysis for fine and coarse aggregate is done, how can we say that those samples are good and how can we say that fine and coarse aggregate by computing the fineness modulus?
What should be the observation and analysis for sieve analysis of fine aggregate if the value of fineness modulus is 3.7, percent error is 1.8%, coefficient of uniformity is 4.1 and Coefficient of curvature is 1.1? Also, what is the conclusion for this?
Show complete solution. Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket = 9.3 Liters Mass of empty bucket = 9 kg Mass of bucket filled with dry-rodded coarse aggregate: Trial 1 = 30.25 kg Trial 2 = 29.76 kg Trial 3 = 31.12 kg a. Calculate the individual dry-rodded unit weight for each trial and the average dry-rodded unit weight of all trials. b. If the bulk dry specific gravity of the aggregate is 2.65, calculate the percent voids between aggregates particles for each trial and the average percent voids of all trials.
Table shows the grain size distributions of aggregates A, and B. Answer the following questions and show all calculations: What are the maximum sizes of aggregates A and B?
What are the main purposes of Sieve Analysis of aggregates? Discuss FIneness Modulus What are the differences between coarse aggregates coming from processing plants and coarse aggregates obtained under water in rivers? What is Gradation? What is Effective size?
A sample of wet aggregate weighed 297.2 N. After drying in an oven, this sample weighed 281.5 N. Theabsorption of this aggregate is 2.5%. Determine the saturated surface dry weight of the aggregates.