Simple Stress and Strain Question 2 At short, reinforced cement concrete column 600 mm x 600 mm has eight steel rods of 25mm 25mm diameter as reinforcement. Find the stresses in steel and concrete, and the elastic shortening of the column if E = 200,000 N/mm² for steel and 10,000 N/mm² for concrete. Load on column= 3000 kN and length = 3 m.

Simple Stress and Strain Question 2 At short, reinforced cement concrete column 600 mm x 600 mm has eight steel rods of 25mm 25mm diameter as reinforcement. Find the stresses in steel and concrete, and the elastic shortening of the column if E = 200,000 N/mm² for steel and 10,000 N/mm² for concrete. Load on column= 3000 kN and length = 3 m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.11P: -11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0...

See similar textbooks

Similar questions

7.5-11 in. cube of concrete (E = 4.5 X 106 psi. v = 0.2) is compressed in biaxial stress by means of a framework that is loaded as shown in the figure. Assuming that each load F equals 25 kips. determine the change iv in the volume of the cube and the strain energy U stored in the cube.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.
An element of aluminum is subjected to tri-axial stresses. Calculate the strains in the element in x, y, and z directions lithe stresses axayand az are -2000 psi, 3500 psi, and 2700 psi, respectively. Assume E = 10,000 ksi and v = 0.33. Also, find the unit volume change of the element.
A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.
A circular aluminum tube of length L = 600 mm is loaded in compression by forces P (see figure). The outside and inside diameters are d2= 75 mm and d1= 63 mm, respectively. A strain gage is placed on the outside of the lube to measure normal strains in the longitudinal direction. Assume that E = 73 GPa and Poissons ratio is v = 0.33. (a) IF the compressive stress in the tube is 57 MPa, what is the load P? (b) If the measured strain is e = 78 J X 10-6, what is the shortening
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
An element of aluminum is subjected to iriaxial stress (see figure). (a) Find the bulk modulus A^for the aluminum if the following stress and strain data are known: normal stresses are v = 5200 psi (tension), a = —4750 psi (compression); and (7_ = —3090 psi (compression) and normal strains in the v and v directions areet = 713,8 X 10_ (elongation) and £y=-502.3 x 10~6 (shortening), (b) If the element is replaced by one of magnesium, find the modulus of elasticity E and Poisson's ratio eif the following data is given: bulk modulus A' = 6,8 x 10 psi; normal stresses are trx= 4550 psi (tension), o", = —1700 psi (compression), and ex= 900 X 10"6 (elongation),
A thin-walled circular tube and a solid circular bar of the same material (see figure) are subjected to torsion. The tube and bar have the same cross-sectional area and the same length. What is the ratio of the strain energy U1in the tube to the strain energy U2in the solid bar if the maximum shear stresses are the same in both cases? (For the tube, use the approximate theory for thin-walled bars.)