SIMPLE STRESSES 15 KN/m 1. The beam shown in the figure carries distributed loads. Design the square (a x a) cross-section of the timber columns of the beam. Column A has the same dimensions 1.50 m 3 m 1 m 10 ΚN/m 1 m as Column B. The strength of the column is 80 MPa. Express the dimensions of the column in whole 10 KN/m A В number.

SIMPLE STRESSES 15 KN/m 1. The beam shown in the figure carries distributed loads. Design the square (a x a) cross-section of the timber columns of the beam. Column A has the same dimensions 1.50 m 3 m 1 m 10 ΚN/m 1 m as Column B. The strength of the column is 80 MPa. Express the dimensions of the column in whole 10 KN/m A В number.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.5.3P: The state of stress on an element of material is shown in the figure. Calculate the unit volume...

See similar textbooks

Similar questions

.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
Determine the maximum tensile, compressive, and shear stresses acting on the cross section of the tube at point A of the hitch bicycle rack shown in the figure. The rack is made up of 2 in. x 2 in. steel tubing which is 1/8 in. thick. Assume that the weight of each of four bicycles is distributed evenly between the two support arms so that the rack can be represented as a cantilever beam (ABCDEF) in the xy plane. The overall weight of the rack alone is W = 60 lb directed through C, and the weight of each bicycle is P = 30 lb.
A unique column has been created with the geometry shown below, where the radius is r = (0.6e-0.08y2) m, the variable y is in meters. The column density of the column material is ρ = 3.21 Mg/m3. Determine the average normal stress at the bottom of the column (y = 0) in units of Pa.
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
Determine the limiting peripheral velocity of a steel ring if the allowable stress is 20 ksi the steel weighs 490lbm /ft^3 . What is the resulting stress if the ring rotates at 6500rpm ? Use r = 10in
A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal pressure of 15 N/mm2 and an external pressure of 5 N/mm2. Determine and sketch curves showing the distribution of the radial and circumferential stress across the section using Lame’s equations.
mechanics of rigid bodies The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4x103 ksi and G brass at 5.2 x 103 ksi. with diagram if necessary.
A solid shaft is required to transmit 90 kW of power at 200 rpm. Determine the shaft diameter by the strength design and rigidity design and from this design choose the suitable diameter of the shaft, if the permissible stress for the material is 50 N/mm2 and the permissible twist is 10 per meter length. Also, determine the maximum shear strain acting on the shaft.Take modulus of rigidity = 150 GN/m2.
find the allowable safe load p if the stresses in the bar are the following : ab=50ksi bc=60 ksi cd= 70 ksi
A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter 40 mm and 5 mm thick. The composite bar is then subjected to an axial pull of 45 kN. If the length of the compound rod is 150 mm , and the elasticity moduli are Est = 200 GPa and Ecu = 100 GPa , determine: 1.2.1 The stresses in the rod and tube
The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating at 2100 rpm. The drive shaft material has an allowable shear stress of 230 MPa. i) Determine the maximum shear stress in the shaft. ii) In order to reduce the weight of the vehicle, a hollow shaft is proposed with a maximum outer diameter of 30 mm. Determine, the maximum inner diameter iii) Determine the resultant percentage weight reduction
The tubular drive shaft for the propeller of a hovercraft is 6 m long. If the motor delivers 4 MW of power to the shaft when the propellers rotate at 25 rad>s, determine the required inner diameter of the shaft if the outer diameter is 250 mm. What is the angle of twist of the shaft when it is operating? Take tallow = 90 MPa and G = 75 GPa.