SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm 啡 F mm. 50 mm 340 mm

SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm 啡 F mm. 50 mm 340 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet DIa 20 mm x=100 mm a. Calculate "P" in KN considering tension failure on gross area b. Calculate "P" in KN considering tension failure on net area c. Calculate "P" in KN considering failure on bearing on projected area. d. Calculate "P" in KN considering failure on shear on rivets e. Calculate "P" in KN considering failure on bearing on block shear f. Calculate the maximum safe load "P" in KN
A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN at D (see figure). Let the dimension variablebe b = 240 mm.(a) Find the minimum permissible diameter dminof the bracket if the allowable normal stress is110 MPa.(b) Repeat part (a), including the weight ofthe bracket. The weight density of steel is77.0 kN/m3.
Determine the minimum diameter of the bolt if the maximum shear stress is equal to 10 ksi. The value of the load P is equal to 4.00 kips.
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa
note: SN = 18, to the topload will be 118kN
Find the value of maximum load P sothat the stresses in the frame illustrated willnot exceed 120MN/m2 in tension or 90MN/m2in compression.The bars of the pin-connected frame shownhave a section of 35mmx65mm each.
The plate shown is fastened to the fixed member to three 10-mm diameter rivets. Compute the value of the loads so that the average shearing stress in the rivet does not exceed 70 MPa. F= 74
A flanged bolt coupling consist of six 10 mm. diameter steel bolts on a bolt circle 300 mm. in diameter, and four 10 mm. steel bolts on a bolt concentric bolt circle of 200 mm. in diameter. (a) Determine the torque applied (N-m) if the shearing stress is 60MPa in the bolts. (b) If the torque capacity increased to 8 kN-m, determine the number of bolts of 10 mm. diameter on the 300 mm. bolt circle of the coupling.
Point B of the system given below is movable support and Enpoint is fixed bearing. According to the given loading condition a) Draw the normal force, moment and shear force diagrams. B) Check whether the section used between AB-BC-CD is suitable, as the material has normal allowable stress em = 85 Mpa and shear strength em = 50 Mpa. c) Find the diameter d of the section used between DE-EF since the normal allowable stress of the material is em = 85 Mpa and the shear strength is em = 50 Mpa.
based on the exercise already solved: A 6mm diameter pin is used in connection C of the pedal shown in the figureIt is known that P = 500N, determine a) the average shear stress in the pinb) the nominal bearing effort at the pedal at Cc) the nominal support effort in each support bracket at C With these data, find:ReactionsMake a cut and find the axial forceDefine cross-sectional area, set dimensions, and find stressFind the factor of safety to be able to select a suitable material
4. The plate shown in the figure is fastened to thefixed member by seven 10-mm-diameter rivets.Compute the value of the loads P so that theaverage shearing stress in any rivet does notexceed 70 MPa.
A horizontal beam AD is supported by an inclined strut CB carries a load W = 2.4KN at the position shown. The strut which consists of one bar is connected to the beam by a bolt passing through the three bars meeting at joint C. BC is 75mm wide and 10mm thick strut while AD is 100mm wide by 10mm thick rigid bar. (a)What is the minimum required bolt diameter in at C if the allowable bolt shear is 68MPa? (b)Determine the stress in strut BC. (c)Determine the bolt stress at A if its diameter is 20mm.