Situation 02. A 0.05KN ball is placed on a vertical circle whose length of the cord is 1.80m. Compute the height (m) measured from the lowest position that the ball will rise on the circular path if the maximum tension the cord can hold is 0.20KN.*

Situation 02. A 0.05KN ball is placed on a vertical circle whose length of the cord is 1.80m. Compute the height (m) measured from the lowest position that the ball will rise on the circular path if the maximum tension the cord can hold is 0.20KN.*

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The porosity of a soil sample is 35%. The specific gravity o sal partides is 2.7. Calculate its woid…

A: The given question is related with geotechnical engineering . In this question we are provided with…

Q: Draw the shear and moment diagram of the following beams: P=74

A: Given:- The magnitude of the varying load = 5P kN/m The value of P = 74 To determine:- Draw the…

Q: Draw a flow net for the weir shown in the Figure. Calculate the rate of seepage under the weir in…

A: We have to draw a flow net for the weir shown in the Figure. Calculate the rate of seepage under the…

Q: A soil has percentage air voids of the order of 30%. It has a porosity of 0.4. The air content of…

Q: Compute for the polar section modulus of an SAE 1060 shafting having a diameter of 3 inches. Use a…

Q: Q-10: Prove that the scale ratio for discharge for a %3D zel^(7)) × HC7) = "D/o where = dischage…

Q: A column carrying a load of 750 kN is to be founded on a square footing at a depth of 2 m below the…

A: We have to determine what will be the size of the footing if a factor of safety of 2.5 is considered…

Q: From the following data of a freeway surveillance, there are 7 vehicles under observation and the…

Q: mm rectangles arranged as shown. A. Determine the maximum value of w without exceeding the…

A: solution of above problem is below:

Q: You use the following distances for a peg test: AM = MB = 50.000 !! PA = 5.000 If Enr is 0.026, E,…

Q: (d) 4 kN/m 2 kN/m |B C 2 m 3 m

Q: a

A: Given open cylindrical tank, with diameter d= 605 mm thickness t = 3.02 mm a= 40.10 MPa, b =…

Q: le of forces at A and system is to be repla

Q: Calculate the error

A: This question has been taken from Surveying engineering and the explanation is given below:

Q: Q3. What is the relative displacement of points A and B when subjected to forces P. Consider only…

A: Relative displacement, which is displacement of a point on a structure with respect to its original…

Q: Determine the kinetic energy flux of 0.02m^3/s of oil (sp. gr. = %3D 0.85) discharging through a…

A: The discharge rate, Q=0.02m3sSpecific gravity of fluid, SG=0.85Diameter of nozzle, ∅=50mm

Q: AREA-VELOCITY METHOD The data pertaining to a stream-gauging site are given below: Distance from the…

Q: A sample of field soil is tested in the laboratory. The results of Standard and Modified Proctor…

A: The ratio of field dry density to maximum dry density ( density corresponding to optimum moisture…

Q: The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load…

Q: 10 lb-ft 50 lb-ft 70 lb-ft (1) (2) 30 lb-ft (3) B

A: Diameter of shaft, ∅=0.86inThere are several torques applied on shaft

Q: Describe at least five (5) orebody configurations that lend themselves to surface mining methods…

A: surface mining: Surface mining is a form of mining in which the soil and rock covering mineral…

Q: 3. A wooden log footbridge in a park is to span 14meters between centers of end supports. Two logs…

Q: Given the following open traverse, the bearing angle of line AB is N 63°12'55" E, and the interior…

Q: Question 3: The 8 kg Block is moving with an initial speed of 5 [m/s]. If the coefficient of kinetic…

Q: Given the properties of the section below: width = 1000 mm thickness = 596 mm concrete cover to bar…

A: given data width, b=1000 mm thickness, D=596 mm Effective cover, d'=90 mm effective depth,…

Q: GIVEN: Weight of the man= 67.50kg Velocity Equation V = 20(6.33 - y); where y is the height measured…

Q: Estimate the submerged height of a steel cube 0.3 m on a side that floats in mercury. The relative…

Q: The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of Tallow =60 MPa.…

Q: PROBLEM 3 SLOPE-AREA METHOD During a flood flow the depth of water in a 12 m wide rectangular…

Q: A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300 kW (shaft…

Q: A railroad tie (or sleeper) is subjected to two rail loads, each of magnitude P = 178 kN, acting as…

A: Given: The value of P is 178 kN. The value of b is 300 mm. The value of h is 250 mm. The value of L…

Q: Situation 01. Using Green-Ampt Infiltration model, calculate the infiltration rate for a sandy loam…

A: Green-Ampt infiltration model: - This model represents infiltration process in simple way in…

Q: Situation 02. An evaporation pan was set-up adjacent to a reservoir. The depth of water in the pan…

Q: A simply supported beam is subjected to a linearly varying distributed load q(x) = q, with maximum…

A: Maximum intensity q0,

Q: 2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm and b is…

Q: Determine the forces in members EH and EI of the double Fink truss (positive if in tension, negative…

A: Solution Find the support reactions VA +VG = 7L But, VA =VG , according to the symmetry So, VA =…

Q: III – Stress Analysis of Trusses 3. Determine the forces FG, EF & AC of the truss 50 kN 150 kN 6 m…

Q: Infiltration capacity data obtained in a floating type infiltration test is given below: Time since…

A: For the given data,

Q: For questions 2A and 2B, refer to the load and shear diagrams below. 2A. What is the slope of the…

A: Slope of shear diagram from B to C is equal to the loading in region B to C. So, answer= 16 KN/m

Q: Gate 16 in. 12 in. turpentine (54.2 pef) (a) Determine the magnitude (in Ibs) and direction (R or L)…

Q: 20 cm 20 cm 20 cm

Q: If the volume of voids is equal to the volume of solids in a soil mass, then the values of porosity…

Q: A soil has percentage air voids of the order of 30%. It has a porosity of 0.4. The air content of…

Q: A cylindrical can is to be made to hold 1 liter of oil. Find the dimensions (in cm) that will…

Q: The beam shown below with a length L = 12 m and a rectangular cross section that has a width of b =…

Q: 70° 70° F2 F1 5m 2m A column of 5m height is subject to 2 forces, F1 = 83N and F2 = 50N as %3D %3D…

A: Resolve the forces F1 and F2 in horizontal direction. Then using the definition of bending moment…

Q: Design rod to support load of 175,000 pounds. What diameter rod is appropriate? Safety Factor, SF=…

Q: 600 KN 240 KN E 16m A B 12m 12m 12m 300 KN 12) Determine the reaction at B. * 715.00 KN 751.20 KN…

Q: Water flows through a pipe at 130 L/s that changes gradually in diameter from 154mm at point A to…

A: solution Given discharge Q=130 Lsec=130×10-3 m3secas the pressure changes from 70kpa to 48.3Kpa so…

Q: Q.10 Athin cylindrical tube closed at ends is subjected to internal pressure. A torque is also…

Question

Pls answer the problem in 3 decimal places thank you..

Situation 02. A 0.05KN ball is placed on a vertical circle whose length of
the cord is 1.80m. Compute the height (m) measured from the lowest
position that the ball will rise on the circular path if the maximum tension
the cord can hold is 0.20KN.*

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The man picks up the 52-ft chain and holds it just high enough so it is completely off the ground. The chain has points of attachment A and B that are 50 ft apart. If the chain has a weight of 3 lb/ft, and the man weighs 150 lb,determine the force he exerts on the ground. Also, how high h must he lift the chain? Hint: The slopes at A and B are zero.
In the gate AB is hinged at B and is 1.2 m wide. What vertical force, applied at the center of gravity ofthe 20kN gate, will keep it in equilibrium?
The crest gate shown consists of a cylindrical surface which AB is the base, supported by a structural frame hinged at C. It is retaining water on one side. The length of the gate perpendicular to the paper is 8.29 m. Use R = 14 meters, and θ = 42°. Determine the distance (in meters) of the vertical component of the hydrostatic force measured from the hinge at C. Round off to three decimal places.
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
Find the centre of gravity of an I-section with top flange 100mn×20mm,wave of 200×30mm and bottom of flange 300×40mm
A swimming pool has a width of 12ft and a side profile as shown. Determine the resultant force the pressure of the water exerts on bottom BC. Inclined BC makes an 14.478 degrees with the horizontal.
Q2) A line AB of slope 3% was measured with steel tape of 30m to be 175.66 m. The weighing of tape was 0.032 m / kg with cross - sectional area of 0.049 cm2 and has length of 30.02m at standard conditions of 20 ° C and a tension of 6 kg. For each time used, it was supported at three points (ends and middle) with tension of 9kg and temperature of 30 ° C. Compute the corrected horizontal distance when the modulus of? elasticity is 2.15 * 106 kg / cm2 and (a = 1.15 * 10-5 / ° C)
The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
Water flows at a rate of 107L /s round a 1510 contracting pipe bend which lies in a horizontal plane. The diameter at the bend entrance is 771mm and at the exit 418mm. If the pressure at the entrance to the bend is 256kN/m2, determine the resultant force in the Horizontal direction (taking to the Left as positive) exerted by the fluid on the bend, correct to the nearest N. (Use π = 3.14)
Compu the ff. 1. Location of Maximum defelction 2.Slope at point a and b 3. Maximum deflection
b) determine the total hydrostatic force of an inclined rectangular gate with water on side as shown Unit of the correct answer: kips