Situation 10. The system shown anchors a stanchion of a cable-suspended roof. If the tension in cable AB is 900 kN, what are the tensions in cables EF and EG? G (0, 1.4, –1.2) m E (3.4, 1,0) m (2, 1, 0) m (1, 1.2, 0) m B (0, 1.4, 1.2) m A (2.2, 0, –1) m D (2.2, 0, 1) m C

Situation 10. The system shown anchors a stanchion of a cable-suspended roof. If the tension in cable AB is 900 kN, what are the tensions in cables EF and EG? G (0, 1.4, –1.2) m E (3.4, 1,0) m (2, 1, 0) m (1, 1.2, 0) m B (0, 1.4, 1.2) m A (2.2, 0, –1) m D (2.2, 0, 1) m C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 1 Cylinder E has a mass of 80 kg and each cable segment can sustain a maximum tension of…

Q: Question 2 The box with weight W is supported by the cable system consisting of cables AB, D AC and…

A: Note- Since we answer three subpart at a time so we will answer the first three. Please resubmit…

Q: Problem Number 1: In the given cable carrying a horizontal uniform load of 10.5 KN/m , and point C…

A: Free body diagram - h1 = 12m h2 = 25m

Q: ermine the tension in each segment of the cable shown in the figure below, also what is on h? 2 m D.…

A: To find tension in cable

Q: Calculate the working stress on the 1/2-inch diameter cable as shown on the figure below. The bar…

A: The values and figure(diagram) given in the question are as follows Diameter of cable(d)=0.5 in…

Q: A flexible cable is subjected to a uniformly varying load. If the tension at the supports is 12 kN,…

Q: Question 4 2 m h D 2 m B 3 kN 8 kN tism- 2 m- -2 m-

Q: 3 m C -3 m 200 N/m B

A: Given data UDL = 200N/M span = 3m we can find the vertical components

Q: A steel plate is hoisted by a cable sling that has clevis at each end as shown in the Fig. The total…

Q: Q2: The cylinder A weighs 450 N and it is supported by the vertical smooth wall and the cable system…

A: Given data Weight of cylinder Angle of rope To find Tension in rope

Q: The triangular trough is hinged at A and held together by cable BC at the top as shown. It retains a…

A: First calculate the hydrostatic force on the side of trough. The calculate the depth of centre of…

Q: Problem 2. A 145 KN fully luaded car is pulled up a surface inclined at an angle 30 degrees from the…

A: Using equilibrium equation

Q: Calculate the smallest area of each cable if the stress is not to exceed 90 MPa in bronze and 120…

Q: A water supply pipeline crossing a wide river is to be supported by a flexible wire cable with an…

A: Given: The allowable tensile load is 20000 kg. The weight of the pipe is 50 kg/m. The total length…

Q: A perfectly flexible and inextensible cable is shown in the figure (not to scale). The external…

Q: ANALYSIS OF STATICALLY DETERMINATE STRUCTURES CABLES AND ARCHES The power transmission cable has a…

Q: A catenary cable shown has a weight of 215.82 N/m. It has a tension of 300 kN at its lowest point in…

A: Tmin=300kNso,H=TminH=wL28h300=0.21582×50028hh=22.4812m

Q: 2. The crate weighs 450 kg and is supported B by three cables as shown in the figure 2m below. 1m 1m…

Q: E 30° C 42° 4 3

Q: A cable supports two vertical loads as shown in Fig. If the maximum tension in the cable is 2000 lb,…

A: The given figure is shown below:

Q: 2. The crate weighs 450 kg and is supported by three cables as shown in the figure 2m below. 1m 1m…

A: As per guidelines we need to answer only first three subparts so please repost rest question…

Q: A to C. WALL B 6 m WALL D 2 m 4 m 6 m 12 kN y A 3 m 3 т 5 т 5 т 25 kN

Q: Two cables A and B had their both ends attached to each other as shown. Cable A is 10 in long and…

Q: For a suspended cable arrangement shown below, the curved length of cable is Q.4 20 m - 30 m h = 6 m…

A: From given arrangement, Here we find curved length of cable.

Q: Problem Number 1: In the given cable carrying a horizontal uniform load of 10.5 KN/m , and point C…

Q: A flexible cable is subjected to a uniformly varying load. If the tension at the supports is 12 kN,…

Q: PROBLEM 3: CATENARY CABLE An 800 m cable weighing 30N/m is supported at ends that are 100 m…

Q: A cable PQ of length 25 m is supported at two ends at the same level as shown in the figure. The…

Q: 2. The crate weighs 450 kg and is supported B by three cables as shown in the figure 2 m below. 1m…

Q: Situation A. | Six steel cables support a circular moulding of diameter 2 meters. The cables are…

A: To determine: minimum diameter of the cables for given allowable stress vertical displacement of…

Q: 2. The crate weighs 45 0 kg and is supported by three cables as shown in the figure below. a. Drawaf…

A: as per our guidelines we are suppose to solve only 3 subparts if multiple are asked. kindly repost…

Q: A shaft of diameter (d = 5-mm) is to be puiled through a (4.5)-cm-diameter glycerin-filled sleeve as…

A: To determine the sleeve length that is required to pull the shaft at the given velocity. Given,…

Q: Cable Analysis : Analyze the loaded cables as shoon. TOO m 10 m 40 kg/m

A: cable is subjected to uniform vertical load so horizontal force at each joint will be equal and in…

Q: Situation X:A series of uniformly spaced hangers along a parabolic cable supports a 60 – m pipeline…

Q: 1. Calculate the mass of the heaviest cylinder that can be supported without exceeding a stress of…

Q: Datum SB 3.) If the cable that is connected to block A slacks with an acceleration of 0.6 m/s/s.…

Q: 1. A cable supports a load of 50 kg/m uniformly distributed along the horizontal and is suspended…

A: Data given: Load of deck = 50 kg/m Asked: Calculate the cable tension at A and B Determine the…

Q: The 25.00 KN crate is to be hoisted with a constant velocity from the hold of a ship using the cable…

Q: Situation 10. The system shown anchors a stanchion of a cable-suspended roof. If the tension in…

A: The vectors can be found using position:- rBA=[(3.4-2) i+(1-1)j+(00)k]mrBA=1.4*ieBA=rBArBA=i The…

Q: A cable supports two vertical loads as shown in Fig. If the maximum tension in the cable is 2000 lb,…

A: Draw free body diagram Consider the moment equilibrium about point A…

Q: Calculate the internal forces in the cable structure below. 4 ft ▼ 2 lb 6 lb 8 ft 8 ft 8 ft

Q: Cylinder E has a mass of 80 kg and each cable segment can sustain a maximum tension of 200 N,…

A: Given: The mass of cylinder E is 80 kg. The maximum tension in the cable is 200 N. Consider the…

Q: A cable is suspended between two supports at the same elevation 300m high and 500 m apart. The load…

A: Given data, Length = 500m Load per metre length = 600kg Sag of cable = 50m To find out the maximum…

Q: The motor winds in the cable with a constant acceleration such that the 20-kg crate moves a distance…

A: wight of block = 20 kg time traveled = 3 sec distance traveled = 6 m friction coefficient = 0.3

Q: 2.2-4 A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard…

A: To determine stretch in cable, total load has to be calculated will be equal to the sum of weight of…

Q: Find sag Yc and determine the largest force, F, that can be sustained by the cables if the maximum…

A: The given figure is shown below: tan θ1=5.84.35θ1=53.13°tan θ2=yC-5.81.4tan θ3=yC-1.051.4

Q: A cable supports two vertical loads as shown in Fig. If the maximum tension in the cable is 1000 Ib,…

A: Free body diagram of whole diagram Consider the moment about point A…

Q: A cable PQ of length 25.m is supported ất two ends at same level as shown in the figure. The…

Q: For the system below, determine the time required for the B load to reach speed of 10 m/s if the…

A: The acceleration in cable A due to motor(aA)=3 m/s2, The target speed for the load B=10 m/sec,…

Q: 1.2m WN/m 1340 N 3.6m

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Situation 10. The system shown anchors a stanchion
of a cable-suspended roof. If the tension in cable AB is
900 kN, what are the tensions in cables EF and EG?
G
(0, 1.4, –1.2) m
(3.4, 1, 0) m
(2, 1, 0) m
(1, 1.2, 0) m
B
(0, 1.4, 1.2) m
A
(2.2, 0, –1) m
D
(2.2, 0, 1) m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Trending now

This is a popular solution!

Step by step

Solved in 8 steps with 16 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the Cable as shown below that weighs 15 N/m with the tensileforce at Point B that is found to be 500 N.Determine the following:a.) The Tension at Point A.b.) The Minimum Tension in the Cable.c.) The Span of the Cable L.
In the given cable carrying a horizontal uniform load of 10.5 KN/m , and point C is the lowest point in the cable. (a) determine the maximum tension (Tmax) on the cable, (b) the cable diameter if the allowable tensile force is 1,450 MPa (c) Length of the cables considering the given sag.
ps5 Given the Cable as shown below that weighs 4.0 N/m with 30 Nhorizontal load applied at the roller support at Point B.Determine the following:a.) The Span of the Cable L.b.) The Maximum Tension in the Cable.c.) The Minimum Tension in the Cable.
7 Given the Cable as shown below that weighs 15 N/m with the tensile force at Point B that is found to be 500 N.Determine the following:a.) The Tension at Point A.b.) The Minimum Tension in the Cable.c.) The Span of the Cable L.
In the given cable carrying a horizontal uniform load of 7.5 KN/m, and point C is the lowest point in the cable, (a) determine the maximum tension (max) on the cable (b) the cable diameter it the alowable tensile force is 1, 450 MP (c) Length of the cables considering the given sag
Problem Number 1: In the given cable carrying a horizontal uniform load of 9.5 KN/m , and point C is the lowest point inthe cable. (a) determine the maximum tension (Tmax) on the cable , (b) the cable diameter if the allowabletensile force is 750 MPa (c) Length of the cables considering the given sag.
For the system below, determine the time required for the B load to reach speed of 10 m/s if the cable in A is pulled by an engine with constant acceleration of 3m/s². Consider that at first the whole system was at rest.
Find sag Yc and determine the largest force, F, that can be sustained by the cables if the maximum tension allowed is 720 N.At point C, what is the largest mass, M, that can be sustained by the cables if the maximum tension is 720 N.What is the tension in cable CD in Newtons (N)?What is the value of sag Yc in meters (m)?
The cable is carrying a horizontal uniform load of 7.5 KN/m, and point C is the lowest point in the cable. Find: 1. The Maximum Tension (Tmax) on the cable. 2. The Cable Diameter if the allowable tensile force is 1.450 Mpa 3. The length of the cables considering the given sag.
Structure Analysis A cable shown in the figure is loaded with two-point loads of 50 kN and 100 KN respectively. The supports are at the same level. Then the tension in the BC portion ___KN.
What is the maximum tension (approximately) in the cable as shown in figure, if it carries a uniform horizontally distributed load of intensity 120 kN/m?
a water supply crossing a wide river is to be supported by a flexible wire cable with an allowable tensile of 20000kg. the pipe weight 50 kg per meter and has a total length of 60m. a. determine the minimum sag of the cable b. determine the tension the lowest point of the cable. c. if the sag is to be 2m. what is the tension at the support?