SITUATION 2 A riveted bracket show in the figure is subjected to load P acting at an angle of e from the vertical. There are 8- 20mm diameter rivets, four on each column flange and two plates one on each column flange. P=35KN, 0 = 60°, a=300mm, b=450mm, e=250mm a. Determine the maximum moment experienced by the bolted connection b. Determine the force due to direct load carried by the most critical rivet c. Determine the force due to the induced moment carried by the most critical rivet d. Determine the maximum resultant load carried by the most critical rivet P ba two plates (One on each column flange) 8 rivets l(4 on each column lange) 0000

SITUATION 2 A riveted bracket show in the figure is subjected to load P acting at an angle of e from the vertical. There are 8- 20mm diameter rivets, four on each column flange and two plates one on each column flange. P=35KN, 0 = 60°, a=300mm, b=450mm, e=250mm a. Determine the maximum moment experienced by the bolted connection b. Determine the force due to direct load carried by the most critical rivet c. Determine the force due to the induced moment carried by the most critical rivet d. Determine the maximum resultant load carried by the most critical rivet P ba two plates (One on each column flange) 8 rivets l(4 on each column lange) 0000

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.19P: A bracket ABCD having a hollow circular cross section consists of a vertical arm AB{L = 6 ft), a...

See similar textbooks

Similar questions

A flat brass bar has length L, constant thickness t, and a rectangular cross section whose width varies linearly between b2at the fixed support to b1at the free end (see figure). Assume that the taper of the bar is small. The bar has modulus of elasticity E. Calculate the displacements ??Band ??cif P = 200 kN, L = 2 m, t = 20 mm, b, = 100 mm, b, = 115 mm, and E = 96 GPa.
A post AB supporting equipment in a laboratory is tapered uniformly throughout its height H (see figure). The cross sections of the post are square, with dimensions b × b at the top and 1.5b × 1.5b at the base. Derive a formula For the shortening 8 of the post due to the compressive load P acting at the top. (Assume that the angle of taper is small and disregard the weight of the post itself.)
A bracket ABCD having a hollow circular cross section consists of a vertical arm AB{L = 6 ft), a horizontal arm BC parallel to the v0 axis, and a horizontal arm CD parallel to the -0 axis (see figure). The arms BC and CD have lengths b}= 3.6 ft and b2= 2,2 ft, respectively. The outer and inner diameters of the bracket are d-, = 7,5 in. and dx= 6,8 in. An inclined load P = 2200 lb acts at point D along line DH. Determine the maximum tensile, compressive, and shear stresses in the vertical arm
An L-shaped reinforced concrete slab 12 Ft X 12 ft, with a 6 Ft X 6 ft cut-out and thickness t = 9.0 in, is lifted by three cables attached at O, B, and D, as shown in the figure. The cables are are combined at point Q, which is 7.0 Ft above the top of the slab and directly above the center of mass at C. Each cable has an effective cross-sectional area of Ae= 0.12 in2. (a) Find the tensile force Tr(i = 1, 2, 3) in each cable due to the weight W of the concrete slab (ignore weight of cables). (b) Find the average stress ov in each cable. (See Table I-1 in Appendix I for the weight density of reinforced concrete.) (c) Add cable AQ so that OQA is one continuous cable, with each segment having Force T, which is connected to cables BQ and DQ at point Q. Repeat parts (a) and (b). Hini: There are now three Forced equilibrium equations and one constrain equation, T1= T4.
Two pipe columns (AB, FC) are pin-connected to a rigid beam (BCD), as shown in the figure. Each pipe column has a modulus of E, but heights (L1or L2) and outer diameters (d1or different for each column. Assume the inner diameter of each column is 3/4 of outer diameter. Uniformly distributed downward load q = 2PIL is applied over a distance of 3L/4 along BC, and concentrated load PIA is applied downward at D. (a) Derive a formula for the displacement
A T-frame structure is composed of prismatic beam ABC and nonprismatic column DBF that are joined at B by a friction less pin connection. The beam has a sliding, support at A and the column is pin supported at F (see figure). Beam ABC and. column segment DB have cross-sectional area A; column segment BF has area 2A. The modulus of elasticity E is the same for both members. Load 2P is applied downward at C, and load P acts at D. Find expressions for the downward displacements of column DBF at D (5D) and also at B (
A vertical post AB is embedded in a concrete foundation and held at the top by two cables (see figure). The post is a hollow steel tube with modulus of elasticity 200 GPa, outer diameter of 40 mm, and thickness of 5 mm. The cables are tightened equally by turnbuckles. If a factor of safety of 3,0 against Euler buckling in the plane of the figure is desired, what is the maximum allowable tensile force Tallowin the cables?
A truss ABC supports a load W at joint B, as shown in the figure. The length L, of member Aß is fixed, but the length of strut BC varies as the angle is changed. Strut BC has a solid circular cross section. Joint B is restrained against displacement perpendicular to the plane of the truss. Assuming that collapse occurs by Etiler buckling of the strut determine the angle for minimum weight of the strut.
The upper deck ala foothill stadium is supported by braces, each of which transfer a load P = 160 kips to the base of a column (see figure part a). A cap plate at the bottom of the brace distributes the load P to four flange pates (:1 = I in)t hrough a pin(d, = 2 in.) to two gusset plates t8 = l.5 in.) (see figure parts b and c). Determine the following quantities. (a) The average shear stress i in the pin. (b) The average bearing stress between the flange plates and the pin and also between the gusset plates and the pin Disregard friction between the plates. Determine the following quantities. (a) The average shear stress i in the pin. (b) The average bearing stress between the flange plates and the pin and also between the gusset plates and the pin (7j )L Disregard friction between the plates.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
A rigid bar AB having a mass M = 1.0 kg and length L = 0.5 m is hinged at end A and supported at end B by a nylon cord BC (see figure). The record has cross-sectional area A = 30 mm2. length b = 0.25 m. and modulus of elasticity E = 2.1 GPa. If the bar is raised to its maximum height and then released, what is the maximum stress in the cord?