Answered: SITUATION 4. The length of curve of a…

SITUATION 4. The length of curve of a simple having a degree of curve 4° is equal to 210m. Compute the middle ordinate of the curve. O 18.03m 19.03m 20.03m 21.03m

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter15: Geometric Design Of Highway Facilities

Section: Chapter Questions

Problem 7P

See similar textbooks

Related questions

Q: Determine the tension in each cable and the components of reaction at D

Q: Which British Standard outlines the BIM Level 3 maturity level? BS 1088 BS 1192 (now ISO 19650) BS…

A: Correct option :- BS 1192 (now ISO 19650 )

Q: Calculate the slope and Deflection at point C. Consider EI as constant and start x from A.

A: Given data EI = constant Find slope and deflection at point C.

Q: An oil of viscosity 5 poise is used for lubrication between a shaft and sleeve. The diameter of the…

A: Given Data- Viscosity μ=5 poise=0.5 Ns/m2, Diameter of shaft D=0.5 m, Speed of shaft N=200 r.p.m,…

Q: Situation 4. Determine the forces for members GF, GD, and CD using Method of Section. Indicate if…

A: Given data in question Load 15, 25 and 10 kN Span 8 m Height 3m To find out Member forces GF, GD…

Q: Determine the force in each member of the truss 2+A m A 1+ B B 5 kN -2 m- Y KN -2 m- D X KN

A: Given: A simply supported truss as shown in the figure. A=1B=5Y=83X=256 Method used: Method of…

Q: The validity of quantity take-offs inherently depends on the quality of the modeled components and…

A: Quantity take-offs (QTO) are precise calculations of the quantity of supplies and manpower required…

Q: The vehicle travels over the hill described by y = ( − 1.5 x 10−³ x²) ft. If it has a constant speed…

Q: Prove the following derivation: meters squared per second

A: Given, Unit of kinematic viscosity = m²/s Viscosity:- it is defined as the Measure of resistance of…

Q: A pipe of diameter 1.5 m is required to transport an oil of specific gravity 0.9 and viscosity…

A: Given Data- Diameter of prototype Dp=1.5 m, Viscosity of fluid μp=3x10-2 poise, Discharge of…

Q: Which is the most common type of BIM model where a specification constrains what can be modeled?…

A: This question is related to the Building design from Civil Engineering.

Q: H 2. 3.4-4 A992 steel is used for the tension member shown in Figure P3.4-4. The bolts are 3/4 inch…

Q: PROBLEM NO. 3 (Arch) Classify the determinacy and stability of the parabolic arch. If the arch is…

Q: The right limb of a simple U-tube manometer containing mercury is open to the atmosphere while the…

A: Given Data- Specific gravity of fluid S1=0.9, Difference in mercury level h2=20 cm, To find- The…

Q: Q- A single degree of freedom system of mass 22 kg and stiffness 17 kN/m vibrates freely. If damping…

Q: SITUATION 4. The length of the curve of a simple having a degree of curve 4° is equal to 210m.…

Q: 4. Compute the volume generated by rotating the area shown through one revolution about the x-axis.…

A: 4. The given figure is shown below:

Q: 1-45. The truss is made from three pin-connected members having the cross-sectional areas shown in…

A: Given Data : Determine the average normal stress developed in each member when the truss is…

Q: piezometer

Q: # 3A. The rigid bar AB, attached to two vertical rods as shown, is horizontal before the load P is…

A: Given, P = 50 kN Lal = 3m Lst = 4m Eal = 70 GPa Est = 200 GPa

Q: 4. Locate the centroid of the shaded area in the figure. y 3cm 6cm 4cm 8cm 9cm 4cm X

Q: A helical spring in which the slope of the helix may be assumed small is required to transmit a…

A: Given data, A helical spring, Allowable shear stress= 110Mpa G=80Gpa Mean diameter of the coil D=…

Q: What is the vadose zone, capillary fringe zone, and phreatic zone

A: Groundwater:- Water that is underground and can be found in voids and cracks in sand, rock, and…

Q: Q- A single degree of freedom system of mass 22 kg and stiffness 17 kN/m vibrates freely. If damping…

A: Given- A single degree of freedom system- Mass m=22 kg, stiffness K= 17 kN/m, Damping in the system…

Q: 9-21. Determine the slope and displacement at point C. Use the principle of virtual work. El is…

A: Given data Find slope and deflection at C using virtual work method.

Q: For a 10% error in the estimation of mean rainfall and for a coefficient of variation of the…

A: Given- Error % e=10%, Coefficient of variation Cv=30, It is needed to find the number of optimal…

Q: List and briefly explain 3 advantages of pipe earthing as applied to earthing systems design

A: Advantages of pipe earthing (i) Pipe earthing is primarily done to earth high-powered machines…

Q: ISO 55000 is an international standard that provides governance for asset management. True False

A: Answer: True

Q: Determine the member forces CD and GF using method of sections. Indicate if (T) or (C)

A: Given Data Find force in member CD and GF using method of section.

Q: a. Sketch the traverse and verify that the traverse has balanced interior angles (assume acceptable…

A: Given: Bearing of course AB=S 74° 30' E. =180°-74° 30'=105° 30'. Interior Angles: ∠A=67° 30'∠B=70°…

Q: PROBLEM 4 The beam shown is loaded with the triangular, rectangular and the 10kN point load. Find…

A: Give data Find resultant of loading diagram. Concept

Q: Classify the plane frame shown as unstable, statically determinate, or statically indeterminate. If…

A: Given: A frame with loading on it To find : Classify structure as determinate, indeterminate and…

Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…

Q: In a distorted model test of the spillway, the discharge and velocity of flow over model were 2 m³/s…

Q: Solve for the maximum reaction at A, shear at C, and moment at D of the beam shown when subjected to…

Q: Classify each of the following trusses as unstable, statically determinate, or statically…

Q: PROBLEM NO. 1 (Beam) Determine the determinacy and stability of the beam and the reactions at the…

Q: SITUATION 1. A simple curve has a central angle of 36° and a degree of curve of 6º. Compute the…

Q: Plz answer it within 30 min I'll upvote Question is in color part

A: Data given - (a) Angular velocity of the barrel wrt to the turret WBT =…

Q: nd cover for project plan ,Cemete

A: The Project Management Body of Knowledge (PMBOK) defines a project plan as: "...a formal, approved…

Q: Whose responsibility is it to create the as-built BIM? Architect / Engineer to complete designers'…

A: This question is related to the Building design from Civil Engineering.

Q: Fluid Kinematics A two dimensional flow is described by velocity components u = 2x and v= -2y. The…

A: Given data u = 2x v = -2y Find discharge between (1,1) and (2,2)

Q: Block 4 slides in the slot in the fixed piece 1. Axis Q2 of crank 2 is fixed on 1. Q2A = 1 1/2 in,…

A: Q2A = 1.5" →Crank AB = 4.5 →connecting rod S = slider 5"8 →offset

Q: An engineered channel with cross section shown in Figure XX has a discharge of 150 cubic meters per…

A: Solution:-

Q: DETERMINE THE CENTROIDAL MOMENT OF INERTIA X W14 X 30 CIOX 15.3 -X 9.12 [231.7mm]

A: Given: Required: Centroidal moment of inertia

Q: he compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin)…

A: as per guidelines we need to answer only 1st 3 subparts of questions

Q: DETERMINE THE CENTROIDAL MOMENT OF INERTIA 12" [300 mm] [150 mm] 5 "[25 mm] * [25mm] [150 mm] [25mm]

A: Given data Find centroidal moment of inertia.

Q: How could BIM models be harnessed for project specifications? Scan component data to assemble specs…

A: BIM:- The process of building information modeling, which is based on 3D models, is the cornerstone…

Q: The curved rod lies in the x-y plane and has a radius of 3 m. If a force of F = 80 N acts at its end…

A: Given Data : F= 80 N Radius = 3m Determine the moment of that force = 80 N about point O?

Q: unit for the coordinates is meters. the pathline that passes through the point (x-1 m, y=1 m) at…

Concept explainers

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.

Question

SITUATION 4. The length of curve of a simple having a degree of curve 4° is equal to 210m.
Compute the middle ordinate of the curve.
O 18.03m
19.03m
20.03m
21.03m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spiral curve having a length of 80 m, the length of throw of the spiral to be 1.06 m. 1. What would be the offset distance at S.C? a. 6.40 m b. 3.28 m c. 4.80 m d. 4.24 m 2. If the central curve having a radius of 280 m, determine the offset distance from the tangent to the first quarter point on the spiral. a. 0.06 m b. 0.10 m c. 0.08 m d. 0.04 m
A 5 degree circular turnout is to connect a railway track, leading due east, to the mouth of the tunnel which is 70m. from the station 7+812. Use Chord Basis. Determine the radius of the curve in meters. Ans. 229.30
Two tangents having an azimuth of 235° and 277° meet at station 30+28.212 are connected by a 330ft spiral curvewith a 5° circular curve used for light rail transit.a) Determine the difference between the external distance of the spiral and the central curve.b) Determine the minimum super-elevation of the curve at the two-thirds of the spiral with the railway width of 15ft. If g= 32.2 ft/s^2c) Determine the stationing of the S.T.
An 80-m spiral curve has an external distance of 20.50m. Determine the length of the short tangent. (Answer: 26.74m) Determine the length of the long tangent. (Answer: 53.35m)
What is the length of a vertical parabolic curve in meter if you know (g1=+2.5%, g2=-1.5%) and elevations of P.V.C , P.V.I and P.V.T are 24.921, 27.557, and 22.836 respectively
A certain horizontal curve has a central angle of 42.2°. If STA PC is 18+363 and STA PT is at 18+708, determine the station of PI.
Given: Design speed = 75kph; G1 = 2%; G2 = -1%; Ss = 170m. Determine the length of vertical curve.
Stationing of P.T. of a compound curve is at 15 + 480.14. I1 = 30°, I2=36°, D1 = 4° and D2 = 5°. What is the length of curve of the second curve? Use arc basis
12. A sag curve is composed of two parabolic curves. BVC and EVC have elevations 250.30m and 246.30m respectively. The grade of the tangents is -3.5% at BVC (1+300) and +5.5% at EVC (1+800). What is the grade of the common tangent? a) 1.25% c) 0.008% b) 0.08% d) 0.8% 13. Compute the deflection angle at the endpoint of the spiral if the length of spiral is 52m and the degree of the central curve equal to 7.5⁰ a) 3.25⁰ c) 3.52⁰ b) 2.35 d) 2.53 14.
The length of spiral easement curve is 100 m with a central curve of radius 300 m. Compute the offset distance from tangent to the second quarter point of spiral. a. 0.923 m b. 0.345 m c. 0.694 m d. 0.423 m
Two Tangents intersects at Sta. 0+550. A compound curve laid on their tangents has the following data. I1 = 31°, I2 = 36°, D1 = 3°, D2 = 5° a) Compute the stationing of P.C, P.C.C and P.T b) If the P.T is moved 15 m out , compute the station of the P.T within the P.C.C on the same point. Show a Clear and Organized solution:
The tangents of a simple curve have bearings of N 75° 12' Eand S 78° 36' E, respectively. What is the central angle of thecurve?