Situation 9 - The 10-kN and 40-kN forces 40 kN are applied to the pins at B and C, respectively. Neglect the weights of the members. 3m 22. Calculate the magnitude of the pin B reaction at A. 10 kN Answer: 67.76 kN 23. Calculate the magnitude of the pin 2 m reaction at F. Answer: 60.91 kN 1m 4 m Figure SP-3.20

Situation 9 - The 10-kN and 40-kN forces 40 kN are applied to the pins at B and C, respectively. Neglect the weights of the members. 3m 22. Calculate the magnitude of the pin B reaction at A. 10 kN Answer: 67.76 kN 23. Calculate the magnitude of the pin 2 m reaction at F. Answer: 60.91 kN 1m 4 m Figure SP-3.20

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.35P: Find the smallest value of P for which the crate in the Prob. 4.34 will be in equilibrium in the...

See similar textbooks

Similar questions

The linkage is made of two homogenous bars of weights shown in the figure. Determine the horizontal force P required to hold the linkage in the position shown.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
Find the smallest value of P for which the crate in the Prob. 4.34 will be in equilibrium in the position shown. (Hint: A rope can only support a tensile force.)
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The three bars are welded together to form a rigid unit that is supported by three slider bearings. Neglecting the weights of the bars, determine the magnitudes of the three bearing reactions caused by the 120-lbin. couple.
Find the force P required to (a) push; and (b) pull the 80-lb homogeneous roller over the 3-in. curb.
The T-bar AEBF is connected to rod CD, with the joint at F being equivalent to a slider bearing. The supports at A and C are slider bearings, and thrust bearings are found at B and D. The two applied forces, which act at the midpoint of the arm EF, are parallel to the y- and z-axes, respectively. Neglecting the weights of the members, draw the FBDs for the entire structure, the T-bar, and rod CD. Determine the total number of unknowns.
A mechanism is used to apply a constant load Q to the seat in the manner illustrated. 1. Determine the following for the angle: - the lengths of LBE and LAB, in m - in degrees, the angles ? and ? 2. Compile the FBDs of members AB, FG, EBH, and GHI in their entirety. 3. Determine the forces involved in the following situations, in Newtons: - FG-member - H-pin - AB-cylinder hydraulic
The boxes each have mass m, and are held stationary by the systems of ropes and ideal (massless,frictionless) pulleys as shown. Shaded regions are fixed supports.Find the tensions in the labeled ropes.Express your answers in terms of mg. Show your work.You do not need to use the full recipe, but do draw free-body-diagrams!Please summarize your results in a table to make marking easier.
Solve for the internal force in members CA, CB, and DB
Figure 1: For the frame shown, determine the magnitude of the pin reaction at B. Neglect the weight of the frame. (2 decimal point, indicate the answer in kN. Ex: 3.87kN just encode 3.78)