Situation I: In figure shown a pulley is subjected to a torque whose value is 420 N- m. The coefficient of friction between the belt and the pulley is 0.40 1. What is the value of T1 to impend slipping? 2. What is the value of T2 to impend slipping? 3. What is the value of the horizontal reaction at the hinge? 0.27 m 420 N-m

Situation I: In figure shown a pulley is subjected to a torque whose value is 420 N- m. The coefficient of friction between the belt and the pulley is 0.40 1. What is the value of T1 to impend slipping? 2. What is the value of T2 to impend slipping? 3. What is the value of the horizontal reaction at the hinge? 0.27 m 420 N-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 15 kg box rests on a horizontal surface attached to a 5 kg box as shown below. Determine the acceleration of the system and the tension of the rope. μs = 0.4 μk = 0.35
A uniform bar AB weighing 424 kN, is fastened by a frictionless pin to a block weighing 200 kN as shown in figure below. At the vertical wall, f = 0.268 while under the block f = 0.20. Determine the force P needed to start the motion to the right.
A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has seven rungs and the rungs are spaced 0.30 m apart, and the top and bottom rungs are 0.30 m from their respective ends of the ladder. Surfaces at A and B both have the same coefficient of friction. If a worker weighs 630 N and stands on the middle rung, determine the minimum value of the coefficient of friction so that the ladder does not slide. Neglect the weight of the ladder.
The figure shows the infinitely rigid bar (ACD) suspended by three steel wires of diameter d and elasticity E, whose maximum allowable stress in the elastic range is σy. On the bar, weighing W, it also exerts a point force P as indicated in the figure. W= 10 [kN], P=5 [kN], d=5 [mm], L=1 [m], b=50 [cm], E=190 [GPa] , σy= 200 [MPa]. a) Calculate the vertical reactions on each of the wires.If applicable, indicate what wires are at risk of collapse b) Calculate the deformations of each wire for the case shown in a) c) Calculate the maximum deformations in each wire so that their behavior remains in the elastic range
The section of a gravity is as shown in the figure. Assume hydrostatic uplift to vary uniformly from full hydrostatic uplift from heel to zero at the toe. Determine the total reaction per unit length at the base of the dam (lbs/foot). Use sp. gr. of concrete = 2.4. x = 19.1 ft.
For the beam loaded as shown in the figure 1, determine the reaction at A in kN using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 4.7 m, b = 18 kN/m, c = 15 kN.
Situation A: A beam is attached to a wire on the one end and is rested to an inclined plane on the other as shown below. Determine the following: 17. Force acting on the cable. Neglect friction. 18. Vertical and horizontal reaction at the inclined plane. Neglect friction. 19. Force acting on the cable. Coefficient of friction = 0.5 20. Vertical and horizontal reaction at the inclined plane. Coefficient of friction = 0.5
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N , and its center of gravity is located at its geometric center ?, the spool has a larger radius ?=0,17 and an inner radius ?=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: ?? μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel. b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
The figure shows the infinitely rigid bar (ACD) suspended by three steel wires of diameter d and elasticity E σy, whose maximum allowable stress in the elastic range is σy. On the bar, weighing W, it also exerts a point force P as indicated in the figure. W= 10 [kN], P=5 [kN], d=5 [mm], L=1 [m], b=50 [cm], E=190 [GPa] , σy= 200 [MPa]. a) Calculate the vertical reactions on each of the wires.If applicable, indicate what wires are at risk of collapse b) Calculate the deformations of each wire for the case shown in a) c) Calculate the maximum deformations in each wire so that their behavior remains in the elastic range
1. A 6 kg slider is released from rest at Point A and slides with negligible friction in a vertical plane along the circular rodshown below. The attached springhas a stiffnessof 520 N/m and an unstretchedlength of 0.6 m.a. Determine the change in potential energy when the slider is at B in joules. b.Determine the change in elastic potential energy when the slider is at B in joules c. Determine the velocity of the slider at B in meters per second.
What is the concentrated load of the rectangular loading as shown in the figure? What is the concentrated load of the triangular loading as shown in the figure? What is the equivalent resultant force and specify its location, measured from point 0.
A transmission tower shown below is subjected to lateral loads as shown. A =4.7 kN, B =6.2 kN, C =7.6 kN Determine the magnitude of the axial force in member EG (in kN). Answer in two decimal places.