SITUATION. Three forces act on a rigid body namely: F₁= 25kN acts from A (0, 1, 2) to B (2, 3, 5). F₂= 30kN acts from A (0, 1, 2) to C (-2, 4, 3) F3 = 40kN acts from A (0, 1, 2) to D (3, -4, -1) Determine the resultant moment of the forces about point E. Point E is located at (-1, -2, -3). 79.86kN-m O 48.85KN 93.74KN O 111.12kN-m

SITUATION. Three forces act on a rigid body namely: F₁= 25kN acts from A (0, 1, 2) to B (2, 3, 5). F₂= 30kN acts from A (0, 1, 2) to C (-2, 4, 3) F3 = 40kN acts from A (0, 1, 2) to D (3, -4, -1) Determine the resultant moment of the forces about point E. Point E is located at (-1, -2, -3). 79.86kN-m O 48.85KN 93.74KN O 111.12kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the moment over the support at B of the beam shown in the figure and the Reaction Forces at support A, B and D.
If the two forces F1 = {100i - 120j + 75k} lb and F2 = { -200i + 250j + 100k} lb act at A, determine the resultant moment produced by these forces about point O. Express the result as a Cartesian vector.
Solve for the moment about point O produced by the forces P and F. The magnitude of P is (4740/2) lb and that of F is (4740/3) lb. The point O is located exactly at the centroid of the section shown.
The coefficient of static friction between the drum and brake bar is μs = 0.4. If the moment M = 35 N ⋅ m, determine the smallest force P that needs to be applied to the brake bar in order to prevent the drum from rotating.Also determine the corresponding horizontal and vertical components of reaction at pin O. Neglect the weight and thickness of the brake bar. The drum has a mass of 25 kg.
Find: Horizontal reaction of support A. Horizontal reaction of support C. Reaction at point B.
Calculate the reaction of Support Ay, Bx and By.
The forces F1={−5i+4j−4k}kN and F2={5i−3j−2k}kN act on the end of the beam. Replace these forces by an equivalent force and a couple of moment acting at point O. (Figure 1) Determine the resultant force. Determine the equivalent resultant couple moment about point O Enter the x, y, and z components of the force separated by commas
The moment of a certain force F is 144 N-m counter-clockwise about O and 12 N-m clockwise about A. If its moment about B is zero, determine the force
The 200-Kg engine block is suspended by the cables AB and AC. The angular ϴ = 40°. The free body diagram obtained by isolating the part of the system within the dashed line is shown. Determine the forces T(AB) and T(AC).
Learning Goal: To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for a static application. As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a=2.0a=2.0 ftft, b=6.0b=6.0 ftft, and c=11.0c=11.0 ftft. The applied forces are F1=1.50F1=1.50 kipkip and F2=2.00F2=2.00 kipkip. Force F1F1 is applied at an angle θ=35∘θ=35∘ with the horizontal. Neglect the weight of the beam. Determine the vertical reaction at A. Determine the horizontal component of the pin reaction at C. Determine the vertical component of the pin reaction at C.
If you know that the line of influence of the reaction force of the joint of the serration in the figure below lies along the member A To bring the truss into equilibrium under the action of force B, find its amount and the reaction of the joint CA .C at a point NΚ10 in vertical
The structure of a beam with single supports is subjected to a moment MA at the pinned end A, an inclined load FB applied at point B, and a uniformly distributed load with intensity q1 on the segment BC. Find the support reactions at joints A and C, then calculate the internal forces at the midpoint of BC. MA= 380 N.m FB = 200 N q1= 160N/m a= 3 m b= 2m