sketch and explain any six work holding devices used on drillind machene with tow diagram

Q: N THE PULL UP PHASE OF WIDE GRIP PULL UP EXERCISE :  Look for excessive joint torques produced by…

A: wide grip pull up- In wide grip pull up more force required for lifting of weight.

Q: E material has inner m'K, the temperatu

A:

Q: What is gyroscopic effect?

A: Angular velocity is defined as the change in the angular position of a body following circular…

Q: Q2 (a) Compare single threaded and multiple threaded screw and state the benefit why it has been…

A: Introduction: Threading is done for fastening two objects or for motion transmission. In swiss…

Q: Analyze the pneumatic problem and design direct and indirect pneumatic circuit diagram with…

A: Direct Activation Pneumatic Circuit:

Q: application of fire points of lubricants and fuels. With pictures

A: Fire point: It is the minimum temperature at which any fluid start to burn or start combustion is…

Q: What is a double-rod cylinder? When would it normally be used?

A: Two types of cylinders are: Single rod cylinder Double rod cylinder.

Q: What is referred to as the torsion formula?

A: Let us consider a shaft subject to the torque at the free end and fixed at the other end.

Q: What are the Bar Cutter's OBJECTIVES/PURPOSE

A: A bar cutter is a machine tool designed to cut bars of metal. There are several types of bar cutters…

Q: 0.1 m². It slides down an inclined the horizontal, at a constant spe he inclined nlane is lubricated

A:

Q: Describe the importance of pigging, bearing and shaft seals.

A: Pigging is defined as the process of pipeline review or maintenance in which various inspection…

Q: Explain the hydraulic press with suitable diagram.

A: Hydraulic press is a device which works on the principle of pascal's law. Pascal's law states that…

Q: Complete the following table for 7 types of Engineer's Hammers. Турes Hand Sketch Uses Description

A:

Q: Reviewed and update Which type of jig do not have base plate? | प्रकार के जिग में बेस प्लेट नहीं…

A: Given Jig To find Jig without base plate

Q: 6.Suggest steps for prevention of wear in bearings

A: The steps for preventing wear in bearing are as given below : 1.Choose the correct bearing design.…

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: the torque required to prod

A:

Q: P.

A:

Q: Define the Crowned Nut and where is it used? Please define the shoulder nut and where is it used

A: Crown-Nuts. An Embed for utilization inside the end of the circular and square area. The Crown-nut…

Q: What particular feature does a solid collet have that makes it safer than a split collet?

A: The feature does a solid collet have that makes it safer than a split collet are following -

Q: give an example of a use for a nut driver

A: Nut driver:Basically Nut driver is a tool used to tightening and loosen the nuts and bolts. In…

Q: Clearly explain the methodology involved in determining torque, power, and efficiency of power…

A: Consider the diagram shown below for the lowering and raising the load. Here, dm: mean diameter of…

Q: (a) Why the connecting rod is made as I section? Why do some connecting rods have hole drilled from…

A: The connecting rod is a mechanical component that connects the engine's piston and crankshaft. In…

Q: What is Axial Load and explain with example?

A: Axial load is the load which act on the body parallel to the axis or perpendicular to the…

Q: 2. Calculate the volume of hexagonal head bolt by measured data at Instruction 1.

A: GivenPart A(tail part).Volume=π4c2DVolume=π4×15.582×40.11Volume=7642.8mm3Part B(Head…

Q: write about what we mean by hydraulic horse power of drill bit (BHHP) and the impact force of the…

A:

Q: Calculate the volume (in ft) of material used in making 350 ft of 2 in. type L copper tubing.

A: Given that, From the table of type L copper tubeFor a 2 in. in nominal size tube:Outside diameter,…

Q: How mary MI4 10.9 bolts used in Vith &s Systen ?

A: ANSWER- 5 BOLTS

Q: standard reference of water content determination is ASTM D 2216 True False flat grooving tool is an…

A: Solution.jpg

Q: orm live load o an impact facte

A: Uniform Dead Load=1klfUniform Live load=2klfConcentrated load=20kImapct factor=30%

Q: What would be the maximum torque T' if a 75-mm-diameter hole were bored through the shaft?

A: (A) The calculation for maximum torque: - From the torsion equation, the formula for torque is given…

Q: on is a rectangular with thic is ground, it is 90% reliable he type of steel that will giv

A: Fmin  =-F2     Fmax=F A safety factor  of 3 for N = 5E8 cycles calculate the mean force by using the…

Q: CII-3. Use reasonable dimensions for this hammer and a loading to show through an analysis why this…

A: The free body diagram of the hammer is given by, Here, F is the human effort.

Q: Define Iron Stirrups

A: Given Stirrups To find Iron stirrups

Q: Describe the different types of hammers.

A: Types of hammer: Claw hammer: This is the most common hammer for general work available with…

Q: which has a coefficient of static friction -What is the maximum speed at which

A: To find minimum speed.

Q: QIDiscuss in detail the effect of the Diameter in the Buckling of hollow shaft

A: Buckling : It is a spontaneously bends from straight beam in to curved shape under an axial…

Q: What is the function of a fixture and a jig? Please also explain the difference of them

A: Jig: It is a device which is used for supporting and holding of a workpiece in a machine tool and…

Q: Why should you not hold work by hand when drilling? What are the safety measures one must take…

A: Solution:   Drilling is a manufacturing process to form a hole in a workpiece.

Q: With neat sketch explain six different bearing failures, causes and cures.

A: Bearing failures, causes and cures

Q: Explain

A: The bubbles-on-a-soda can task is an example of Charles’ law, which is defined as a for constant…

Q: made of steel with elasti d with the help of free be

A: Diameter of bolt, d=10 mm,Cross section of rectangular plate, A=12 mm× 7 mmTension in the bolt,…

Q: A/ What is kind of shaft bearing illustrated in Figure (1), when it used. Draw side sectional view…

A:

Q: Why is it better to have hollow bars if they are being twisted?

A: If hollow and solid bar have the same radius then solid bar would resist slightly more torque. in…

Q: Define and discuss the hole and shaft basis system with diagram? Briefy explain.

A: Hole basis system In hole basis system the size of the hole remains constant and the shaft size is…

Q: Briefly describe the function of generator in term of sparking purpose and list down 2 main types of…

A: Given: Briefly describe the function of generator in term of sparking purpose and list down 2 main…