FigureSm8/15m02m4m<1 of 16m/1Part ADetermine the component of the angular momentum H of particle A about point Pusing scalar notation.Suppose that m-3 kg. (Egure 1)Express your answer to three significant figures and include the appropriate units.km²(Hr),62.8...SAMPrevious Answers✔CorrectPart BDetermine the component of the angular momentum Hp of particle B about point Pusing scalar notation.Suppose that m-4 kg-Express your answer to three significant figures and include the appropriate units.HÁ→?(Hr), ValueUnitsSubmitNext >Provide FeedbackRequest Answer

Answered: Image /qna-images/answer/32ee54c6-7d8b-4282-aaae-be144df43687.jpg

Answered: Sm 8 m/s 15m 0 AI 6 m/s

Engineering

Mechanical Engineering

Sm 8 m/s 15m 0 AI 6 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block. NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
Asubject of mass 65 kg has her gait analyzed. Suppose that the x componentof the force measured by a force plate takes the shape shown in Fig. (a) If the forward velocity of the walker is 2 m/s at heel strike, what is it0.4 s after heel strike?(b) Estimate the corresponding change in height for the subject’s center ofgravity (i.e., from heel strike to 0.4 s later).
A team of jubliant engineering students, celebrating winning a designcompetition, fires their potato gun straight up into the air. (a) Assuming a quadratic airdrag on the potato with magnitude F (v) = mkv^2, and taking +y to be the upward direction,show that the potato speed varies with height above the ground according to the equations:
As a young engineer, you have been tasked to select the location of a wind turbine based on the details of the location and relevant specification below:Air densityAverage air velocityDiameter of wind turbine bladesLOCATION A1.29 kg/m3 54 km/h 70 mLOCATION B1.21 kg/m3 63 km/h 60 m By comparing the amount of power generated (in MW) at Location A and Location B, determine the location that will give the optimum wind power generation.9 kg of Refrigerant 134-a is initially at 26.69°C with enthalpy of 100 kJ/kg. Heat is transferred to the refrigerant under a constant-pressure process until the entropy of the refrigerant reaches 0.9795 kJ/kg.K.(i) Determine the final temperature of the refrigerant(ii) Calculate the boundary work, Wb, in kJ.Assist your answer with a proper P-v diagram indicating the properties,process, and boundary work region clearly.(iii) Explain the reason behind the high amount of boundary work obtained in (ii).Assist your explanation with relevant sketching.
Topic: Impulse and Momentum Sand drops at a rate of 2000 kg/min from the bottom of a hopper onto a belt conveyer moving horizontally at 250 m/min. Determine the force needed to drive the conveyer, neglecting friction.
Given the following: Mass of the particle m=18.8 kg, ω=9.6 rad/s, α=8.3 rad/s^2, vrel=7.8 m/s, μs=0.6, μk=0.1, L=1.9 m, and h=2.9 m, What is the i^ component of the Normal force on particle P? What is the component of the friction force in the j^ direction on the particle? What is the value (including sign) of (aP/O)rel? What is the i^ component of the Acceleration of particle P? What is the j^ component of acceleration of particle P?
A steel wire connects two trains at rest on the same track. The wire will snapif it is stretched by as much as 1 percent. The trains begin to accelerate in such away that their velocities, as measured in the ground frame, are always equal.Eventually, the wire snaps. Explain carefully why this happens. How fast are thetrains moving when the wire snaps?
Assuming that there are no heat effects and no frictional effects, find the kinetic energy and speed of a 3220-lb body after it falls 778 ft from rest. Start with the steady flow equation, deleting energy terms which are irrelevant.Answer: 224 fps
7. Assuming the there are no heat effect and no frictional effects, find the speed of a 3220 lb body in fpm after it falls 778 ft from rest. Start with the steady flow equation, deleting terms which are irrelevant.
list down the derivation of formulas and describe each variable of "Impulse and Momentum" (Dynamics of rigid bodies)
please I need an answer for this A water jet is deflected 180 degree in a curved vane with diameter of 25.5mm and velocity of jet of 6.5m/s. Determine the force that the jet exerts on the stationary vane Group of answer choices 234 23.4 43.2 34.2
Please do this specific question with these specific data as many have post it with different data! The ABC lift is at rest. You want to estimate the momentum that ABC exerts in C if the weight of A is 105 kg. AB is 12.15 m and weighs 400 kg, BC is 2.7 m and weighs 150 kg. Approximate AB and BC as evenly thick everywhere and homogeneous. Point A is 13.5 m above C in height and B is 2,025 m above C in height. A) What is the moment of force that ABC exerts in C if positive value is counterclockwise in the image? B) If AB instead weighs 150 kg and BC weighs 400 kg, but all other quantities are the same, calculate the torque in C.What is the moment of force that ABC exerts in C with these masses, if positive value is counterclockwise in the picture?