Solve for Q in Watts. The dimension of the wall into the page is 24 mm and the temperature difference between the ou surfaces is 98°C. Write your answer to three decimal places. kA = 20, kg = 0.6, kc = 5, kD = 50, kɛ = 0.6, kp = 0.3, kg = 0.65 al W/m°C. 10 mm 10 mm 20 mpm 10

Solve for Q in Watts. The dimension of the wall into the page is 24 mm and the temperature difference between the ou surfaces is 98°C. Write your answer to three decimal places. kA = 20, kg = 0.6, kc = 5, kD = 50, kɛ = 0.6, kp = 0.3, kg = 0.65 al W/m°C. 10 mm 10 mm 20 mpm 10

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.74P: A manufacturer in the United States wants to sell a refrigeration system to a customer in Germany....

See similar textbooks

Similar questions

The rate of heat flow per unit length q/L through a hollow cylinder of inside radius ri and outside radius ro is q/L=(AkT)/(rori) where A=2/(rori)/ln(ro/ri). Determine the percent error in the rate of heat flow if the arithmetic mean area (ro+ri) is used instead of the logarithmic mean area A for ratios of outside-to-inside diameters (Do/Dj) of 1.5, 2.0, and 3.0. Plot the results.
A manufacturer in the United States wants to sell a refrigeration system to a customer in Germany. The standard measure of refrigeration capacity used in the United States is the ton (T); a 1 T capacity means that the unit is capable of making about 1 T of ice per day or has a heat removal rate of 12,00 Btu/h. The capacity of the American system is to be guaranteed at 3 T. What is this guarantee in SI units?
Using the information in Problem 1.22, estimate the ambient air temperature that could cause frostbite on a calm day on the ski slopes. 1.22 In order to prevent frostbite to skiers on chair lifts, the weather report at most ski areas gives both an air temperature and the wind-chill temperature. The air temperature is measured with a thermometer that is not affected by the wind. However, the rate of heat loss from the skier increases with wind velocity, and the wind-chill temperature is the temperature that would result in the same rate of heat loss in still air as occurs at the measured air temperature with the existing wind. Suppose that the inner temperature of a 3-mm-thick layer of skin with a thermal conductivity of 0.35W/mKis35C and the air temperature is 20C. Under calm ambient conditions the heat transfer coefficient at the outer skin surface is about 20W/m2K (see Table 1.4), but in a 40-mph wind it increases to 75W/m2K. If frostbite occurs when the skin temperature drops to about 10C, do you advise the skier to wear a face mask? What is the skin temperature drop due to the wind?
An air-cooled condenser has an expected U value of 30 W/m2∙K based on the airside. The condenser is to transfer 60 kW with an airflow rate of 15 kg/s entering at 35°C. If the condensing temperature is to be 48°C, what is the required airside area in m2? Round your answer to 2 decimal places.
Note: 1 Torr= 0.133 kPa & 1 atm = 101.325 kPa
Problem 1: A certain rigid aluminum container contains a liquid at a gauge pressure of P0 = 2.02 × 105 Pa at sea level where the atmospheric pressure is Pa = 1.01 × 105 Pa. The volume of the container is V0 = 2.15 × 10-4 m3. The maximum difference between the pressure inside and outside that this particular container can withstand before bursting or imploding is ΔPmax = 2.41 × 105 Pa.For this problem, assume that the density of air maintains a constant value of ρa = 1.20 kg / m3 and that the density of seawater maintains a constant value of ρs = 1025 kg / m3. Part (a) The container is taken from sea level, where the pressure of air is Pa = 1.01 × 105 Pa, to a higher altitude. What is the maximum height h in meters above the ground that the container can be lifted before bursting? Neglect the changes in temperature and acceleration due to gravity with altitude. Part (c) Choose the correct answer from the following options. The depth below the surface of the ocean…
Directions: Show your complete solutions and box your final answer. Do not round off in between the solutions but round off your final answer to the nearest ten thousandths place(4 decimal places). 1. A fluid enters a machine at 170 m/s, 800 kPa, and with a specific volume of 0.3 m^3/kg. The radiation heat loss is 25 kJ/kg. The internal energy decreases by 495 kJ/kg. If the fluid leaves at 330 m/s, 138 kPa, and 0.95 m^3/kg, determine the work done by the fluid in kJ/kg.
An air-cooled condenser has an expected U value of 30 W/m2∙K based on the airside. The condenser is to transfer 60 kW with an airflow rate of 15 kg/s entering at 35°C. If the condensing temperature is to be 48°C, what is the required airside area in m2? Round your answer to 2 decimal places. heat transfer
Convert the following into S.I. units, show complete solution, Do not use conversion table in getting the direct equivalent of Psi, Psf, KPa, Pa, ft-lb, Etc. go for the basic and show the solution 1) 400 N-m/Sec to HP 2) 726,000 lbs to MN 3) 104 Psi to MN/m2 4) 222 GPa to Kg/mm2
11. A 2-kW electric resistance heater submerged in 5-kg water is turned on and kept on for 10 min. During the process, 300 kJ of heat is lost from the water. Solve for the temperature rise of water. (3 DECIMAL IN FINAL ANSWER PLS)
A thermometer reads 90C initially and is placed in a room of temperature 21C. After 2 minutes, the thermometer reads 60C. Determine when will the thermometer reads the room temperature.
An electronics device generates 37.5 W of heat energy during normal operation. The heat is dissipated from the top surface of the device to ambient air at 21°C. If the top surface area is 0.166 m2 and the convection heat transfer coefficient is 7.297 W/m2· K, what will be the surface temperature (in °C) of the device [round your final answer to one decimal place]?