In the refrigeration experiment you obtained the following values while using the fixed orifice valve: 1- absolute pressure at the valve inlet: 680 kPa 2- absolute pressure at the valve outlet: 186.7 kPa 3- temperature at the compressor outlet: 86.67°C What is the value of the compressor work per unit mass in kJ/kg? You can round your result to one decimal place

In the refrigeration experiment you obtained the following values while using the fixed orifice valve: 1- absolute pressure at the valve inlet: 680 kPa 2- absolute pressure at the valve outlet: 186.7 kPa 3- temperature at the compressor outlet: 86.67°C What is the value of the compressor work per unit mass in kJ/kg? You can round your result to one decimal place

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air is expanded in a frictionless piston cylinder arrangement at a constant pressure of 200 kPa from a volume of 0.1 m3 to a volume of 0.3 m3. Then the temperature is held constant while expansion occurs until the final volume is 0.8m3. What is the total work done by the air? Give your answer to one decimal place
Determine the mass of cooling water in kg/s for a water cooled air-conditioning system that uses R22 with condenser size of 253.7 kW Temperature at the cooling water loop are given as follows: 39.9 °C entering the cooling tower 32.6 °C at the inlet of the condenser 60.6 °C refrigerant temperature at the condenser Answer in three decimal places.
A fluid flowing in a pipe 1000 ft above the reference line at a pressure of 200 psia, specific volume of 2 ft3 /lb, velocity of 200 ft/sec and internal energy of 100 Btu/lbm. Determine (a) the total energy of the flowing fluid with respect to the reference line and (b) the specific enthalpy in Btu/lbm . Local gravity is 32 ft/sec2 .
1) Given 753.06 kW electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(10^5) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Answer the following: a) Calculate the exergy destroyed in the process below. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The products of combustion leave this process at the dead state. Process: 0.015 kg is the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of the problem above. if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. b) The utility providing the…
415. An airplane weighing 19903.13 lbf at ground is flying at an altitude of 32, 247.95 ft at 591 miles per hour. Determine the change in potential energy in hp-min
A 4-kW resistance heater in a water heater runs for 3 hours to raise the water temperature to the desired level. Determine the amount of electric energy used in both kWh and kJ.
The average atmospheric pressure on earth is approximated as a function of altitude by the relation Patm 5 101.325 (1 2 0.02256z)5.256, where Patm is the atmospheric pressure in kPa and z is the altitude in km with z = 0 at sea level. Determine the approximate atmospheric pressures in Atlanta (z = 306 m), Denver (z = 1610 m), Mexico City (z = 2309 m), and the top of Mount Everest (z = 8848 m).
26.) Nitrogen with a mass of 3.82 kg expands at constant pressure. The initial pressure and temperature in the piston-cylinder system are 172 kPa and 23°C, respectively. Because of the heat transfer, the system reached a final temperature of 206.2°C. Compute for the work in kJ.
.A high altitude chamber chamber , the volume of which is 30m3 , is put into operation by reducing the pressure from 1.013 bar to 0.35 bar and temperature from 27 0C to 5 0C . How many kg of air must be removed from the chamber during the process ? Express this mass as a volume measured at 1.013 bar and 27 0C Take R=287 J/kg K for air
A gas-filled piston-cylinder unit with volume 2 m³ compressed and pressure 100 kpa. On the piston page. An nika constant spring of 200 kN/m . The units are then heated and Causes the volume of gas to increase to three times the volume of the original, which is pressing Springs. If it is known the surface area of the unit is 0.3 m² radius, a). The final pressure in the cylinder B) A work done with gas c) A work done with springs
In determining the average rate of heating of a tank of 20% sugar syrup, thetemperature at the beginning was 20°C and it took 30 min to heat to 80°C. Thevolume of the sugar syrup was 50 ft3 and its density 66.9 lb/ft3. The specific heat ofthe sugar syrup is 0.9 Btu lb-1°F-1.(a) Convert the specific heat to kJ kg-1°C-1.(b) Determine the rate of heating, that is the heat energy transferred in unit time, in SI units (kJ s-1)
A fluid, contained in a horizontal cylinder fitted with a frictionless leak proof piston, is continuously agitated by means of a stirrer passing through the cylinder cover. The cylinder diameter is 0.40 m. During the stirring process lasting 10 minutes, the piston slowly moves out a distance of 0.485 m against the atmosphere. The net work done by the fluid during the process is 2 kJ. The speed of the electric motor drivingthe stirrer is 840 rpm. Determine the torque in the shaft and the poweroutput of the motor.