Answered: Solve the absolute maximum bending…

Solve the absolute maximum bending moment and absolute shear force in the simply supported beam shown due to the series of moving concentrated loads as shown. 6 k 2k4k 3 k 5 ft 3 ft 3 ft -30 ft-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 11P

See similar textbooks

Related questions

Q: Which of the following has the highest accident rate of all of the building trades? A. HVAC…

A: Concept- HVAC installation- It stands for Heating, Ventilation, and air-conditioning. Carpentry-…

Q: An aluminium alloy (density 2600 kg/m³) casting is to be produced. A cylindrical hole of 100 mm…

Q: slone and deflection of the simply-supported beam shown at point B and point D. Use Conjugate Bea

Q: In an intersection collision, one of the vehicles leave 165 ft of skid marks. A skid mark analysis…

Q: t 4#9 1) fé= 5000 psi r Grade 60 steel; 4 #9 Rebars, 5-9" t 4#9 NWC, 5-9" L = 25 ft & Mn = ? 4#9 14"…

A: Given: fc = 5 ksi fy = 60 ksi L = 25 ft bars = 4-#9 #9 rebar = 1.128 in The breadth of the flange,…

Q: Determine the force in each member of the loaded truss. Explain why knowledge of the lengths of the…

Q: Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in…

Q: The air around the spinning baseball in the following figure (top view) experiences a faster speed…

A: Given data:- The given time taken to travel, 18.44 m The given traveling speed in x direction, 40…

Q: For a BOD test carried out in the laboratory, 5ml of wastewater having no initial DO was taken in a…

A: Given- BOD test- Volume of sample Vs=5 mL, Initial DO = 0, 300 mL BOD bottle, DO of dilution water…

Q: For a sandy soil, the ultimate bearing capacity of 30 cm plate is found to be 120 kN/m² cm during…

A: Given: Width of platebp=30 cm Width of square footingbf=80 cm Ultimate bearing capacity of…

Q: Briefly discuss the characteristics of Figure 7.4 in May’s textbook.

A: Given data- A contour map from Santa Monica Freeway Surveillance system given. To Find- The…

Q: Solve Prob. 6.125 when (a) ß = 0, (b) ß = 6°.

A: Answer (a) β=0 Let us draw free body diagram of forces acting on the system AC and CE On…

Q: Calculate the cross-sectional A₂, and As of the left board (1), the flange board (2), and the right…

Q: An orifice meter with orifice diameter 15 cm is inserted in a pipe of 30 cm diameter. The pressure…

A: Given- Diameter of orifice do=15 cm, Diameter of pipe d1=30 cm, Specific gravity of oil So=0.9,…

Q: Q6 Draw the influence line for the force in (a) member JI, (b) member IE, and (c) member EF. L K 1 H…

A: Given data:

Q: Q1

A: Two beams are given with loadings as shown. Beam 1 is simply supported at the end, one end is…

Q: Determine the the force in member GJ of the truss and tate if this member is in tension or…

A: Given that : F = 1050 lb Intro : 1- It is asked to determine the forces in member GJ and GC of the…

Q: defined by the equation y=0.08.x². At the instant x - 10 m, the toboggan's speed is 5 m/s. At this…

Q: A water treatment plant treats 6000 m³ of water per day. As a part of the treatment process,…

A: Given- A water treatment plant- Discharge Q=6000 m3/day, Discrete settling of the particles,…

Q: A Makeshift Elevator While exploring an elaborate tunnel system, you and your team get lost and find…

A: Given data:- The given bucket weight is,150 lb The given lightest member weight is, 125 lb So the…

Q: . The distance between Duhok and Erbil on the map scale of 1:2000 000 was measured 12cm. Then…

Q: 30. An A992 W21×111 is used as a column in a building to support a dead load of 120 kips and a live…

Q: 200 lb Part A 100 lb/ft 4 ft 300 lb-ft ---10-- Draw the shear diagram for the shaft. The support at…

Q: Use the method of sections and determine the forces on bars CG, EG, and EH for the truss shown. 50…

A: A truss pinned at A and roller supported at B is given. Degree of static indeterminacy, Ds Ds=…

Q: The head loss for a laminar incompressible flow through a horizontal circular pipe is h₁. Pipe…

Q: Based on the bridge truss show below determine the force acting at members DF, GI, and LM using…

A: Given: A simply supported symmetrically loaded truss with hinge support at A and roller support at…

Q: 1) You have used a Manning n value of 0.009 for the open channel in the lab. You would expect…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: Please redo problem do all sections of the beam determining the shear and moment throughout as…

Q: 4. Use the method of sections to determine the force in members AB, BC, IJ, and JK in the K-Truss…

A: A K-truss is given with a downward point load applied at the joint I To determine (using the method…

Q: Activity 2: Use Virtual Work method to solve for the slope at joint F, horizontal deflection at…

Q: Determine the force on each member of the truss and state if the members are in tension or…

Q: If the pitch is 60 mm and rivet value is 40 kN, the number of rivets required for a riveted…

A: Given- Pitch p=60 mm, Load P=150 kN, Eccentricity e=300 mm=0.3 m, Rivet value Rv=40 kN,

Q: 2. Determine the member end moments and reactions for the frame shown. B 1.5 k/ft 20 ft El constant…

Q: Determine the absolute maximum sheur & moment in the simply Supported bridge shown in fig, due to…

Q: Solving for a force and its angle and angle of two forces with given resultant Forces F, P, and T…

A: Given Data (a).Find the value of F and α, if T = 450 N, P = 250 N, β=30°, and the resultant is 300…

Q: Flash floods will occur ....... A. when the soils have a high infiltration capacity…

A: Reference : Geo technical Engineering, Flood and types of floods. Given : A multiple choice question…

Q: Determine the force in member CG of the truss if P₁ = 107 kN and P₂ = 187 kN. Input tension as…

Q: Determine by direct integration, find the centroid (x, y) of the cross-hatched area as shown below.…

A: A parabolic segment in which the corrdinates of centroid are to be found.

Q: 5.24 Water enters the horizontal, circular cross-sectional, sudden- contraction nozzle sketched in…

A: Given data in question Velocity 25 ft/s at section 1 Velocity 100 ft/s at section 2…

Q: A beam with an overhang is supported and loaded as shown in the figure below. The beam has widths w₁…

A: Given data: w1=1 in, w2=0.4 in, h=3.2 in The given beam is statically determinate beam and can be…

Q: Classify the soil according to Unified soil classification. Explain each classification

A: Given Data: The sieve number and mass retained have been given in the problem. To Determine:…

Q: A simply supported beam carries three concentrated loads as shown in the figure. a. Determine the…

A: A simply supported beam is given of span length of 24ft. On this beam, three concentrated loads…

Q: Flow Section 5.2.1 Linear Momentum-Uniform (also see Lab Problems 5.98, 5.99, 5.100, and 5.101) 5.22…

Q: Q3 Draw the shear and moment diagrams for each member of the frame. Assume the frame is pin…

A: The given figure is shown below:

Q: Draw the Axial Force Diagram (NFD), Shear Force Diagram (SFD) and Bending Moment Diagram (BMD) for…

A: Given: Required: Axial force, shear force and bending moment diagram

Q: Liquid Limit Determination Can no. Mass of wet soil + can Mass of dry soil + can Mass of can Mass of…

A: Given: Can no. A1 A18 63 53 132 Mass of wet soil + can 31.7 33.9 40.4 35.3 36.6 Mass of dry…

Q: Determine the forces in members BC and BG of the loaded truss. 4.4 kN 2m 4.4 kN

A: Given : Determine the forces in member BC and BG of truss ?

Q: Q-A railway curve of 1350 m radius is to be set out to connect two tangents. If the design speed is…

A: Radius R=1350 m, Design speed=110 kmph, Rate of change of acceleration c=0.3 m/s2,

Q: Problem-05, A section line AB appears to be 10.16 cm on a photograph for which the focal length is…

A: Given data- Appeared length AL=10.16 cm, Focal length f=16 cm, Length on map ML=2.54 cm, Scale…

Q: A 6m El = constant E = 50 GPa I= 135(106) mm² 70kN-m Determine the slope and deflection at point b…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

BLEM 1
Solve the absolute maximum bending moment and absolute shear force in the simply
supported beam shown due to the series of moving concentrated loads as shown.
6 k
3 k
2k4k
5 ft 3 ft 3 ft
-30 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction and given data

VIEW

Step 2 Absolute maximum bending moment

VIEW

Step 3 Absolute shear force

VIEW

Step 4 Final answer

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

5-Draw the shear force and bending moment diagram for the loaded simply supported beam as shown below. Also mark all salient point of shear force and bending moment values in the diagram with proper units. locate the point where the shear force changes its sign from "+" to "-" and the value of maximum bending moment. where F1=280N, F2=290N, w=14N/m, a=2 m, b=2 m, c=2 m, d=5 m, e=3 m The reaction at the support "A" in N is = ________________ The reaction at the support "B" in N is = ________________ The shear force at the point "A" in N is = _________ The shear force at the point "C" in N is = _________ The shear force at the point "D" in N is = _________ The shear force at the point "E" in N is = _________ The shear force at the point "P" in N is = _________ The shear force at the point "B" in N is = _________ The value bending moment with respect to "B" in Nm is = __________ The value bending moment with respect to "P" in Nm is = __________…
Question No 2: Determine the internal shear and moment acting at a section passing through point C in the beam shown in the figure. Joint A has pin support while joint B has roller support Use R=156
Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the bending moment 6.2 m to the right of point Aif W = 9.6 kN/m, T = 16.23 kNm, m = 8 m, and n = 3.9 m.
For the beam shown, determine the maximum postive bending moment at point B due to the series of four moving concentrated loads.
The vertical force F acts downward at A on the twomemberedframe. Determine the magnitudes of the twocomponents of F directed along the axes of AB and AC.Set F = 350 lb.
(a) Figure Q2 shows a frame with tie rod at joint B and C. The beam carries a concentratedload 300kN at span BC. Analysis and sketch the shear force and bending-momentdiagram for the entire frame.
Draw Shear Force Diagram and Bending Moment Diagram for the compound beam shown.Hinge at B
Problem 1) The beam AC is simply supported at A and C, having a cross section of 50 mm wide by 150mm high is subjected to the uniformly distributed load of 250 N/m plus the couple of magnitude1,500 N-m as shown in Figure 1- A.a) Draw the shear and moment diagrams.
A beam with simple supports is subjectedto a trapezoidally distributed load (see figure).The intensity of the load varies from 1.0 kN/m atsupport A to 2.5 kN/m at support B.(a) Draw the shear-force and bending-moment diagramsfor this beam. Assume that M0 at B is zero.(b) Find the required moment M0 at B so that themaximum moment in the beam does not exceed1.0 kN.m.
Determine the bending moment M in the cantilever beam at the point located 1.44 ft. to the right of point B. The ground reactions and shear-force diagram are shown. a. 8.53 kip-ft b. 10.60 kip-ft c. 6.55 kip-ft d. 7.44 kip-ft e. 11.56 kip-ft
Determine the maximum shear force and bending moment in the beam given that L1=L2=L3= 3m, F1= 12kN, F2= 14kN, F3=16 kN
Determine the shear moment diagram, maximum shear and location of zero or maximum moment in the beams in kN/m.