Split Samples. An industry and a municipal wastewater treatment plant disagreed about wastewater concentrations of total Kjeldahl nitrogen (TKN) and total suspended solids (TSS). Specimens were split and analyzed by both labs, and also by a commercial lab. The results are below. Give your interpretation of the situation. Specimen 1 2 3 4 5 6 7 Muni. 1109 1160 1200 1180 1160 1180 1130 TKN Ind. 940 800 800 960 1200 1200 900 Comm. 1500 1215 1215 1155 1120 1120 1140 Muni. 1850 2570 2080 2380 2730 3000 2070 TSS Ind. 1600 2100 2100 1600 2100 2700 1800 Comm. 1600 1400 1400 1750 2800 2700 2000

Split Samples. An industry and a municipal wastewater treatment plant disagreed about wastewater concentrations of total Kjeldahl nitrogen (TKN) and total suspended solids (TSS). Specimens were split and analyzed by both labs, and also by a commercial lab. The results are below. Give your interpretation of the situation. Specimen 1 2 3 4 5 6 7 Muni. 1109 1160 1200 1180 1160 1180 1130 TKN Ind. 940 800 800 960 1200 1200 900 Comm. 1500 1215 1215 1155 1120 1120 1140 Muni. 1850 2570 2080 2380 2730 3000 2070 TSS Ind. 1600 2100 2100 1600 2100 2700 1800 Comm. 1600 1400 1400 1750 2800 2700 2000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Sanitary Engineering Potential of Hydrogen (pH) same question please help me: 1-What are alternative methods for determining the pH of aqueous samples?2- What are typical pH values of drinking water in Jordan? How do your datacompare with these values?3-Discuss the relationship between (a) pH and hydrogen ion concentration (b) pHand hydroxide ion concentration?
Q 01: a) How can you calculate BOD value? What happens if you have a higher BOD value? b) Differences between COD and BOD? Subject: environmental engineering ii lab
please explain sampling from a static slurry
Q3 (a) Describe briefly the main objective water quality and state the mainparameters involved in water quality analysis.(b) Determine the equivalent weight, concentration of each ion in mg/L as CaCO3and total hardness of the following water sample in Table Q3 (b).(c) 50 mL of wastewater sample has been diluted in a 300 mL BOD bottle forBOD5 20°C analysis. Assume that initial DO is 8.8 mg/L, whilst DO at the end of5 days is 4.5 mg/L, calculate the dilution factor (P) and estimate the value ofBOD5 20°C for the wastewater sample.
The sedimentation tank is due for cleaning and its volume will be drained into half. The tank has a uniform cross-section area of 10m by 10m and currently filled at depth of 6 meters. If the orifice drainer has a coefficient of 0.90 and diameter of 5 centimeters, how much time in seconds would it take to reach the desired level for cleaning? The correct answer has a margin of 10 seconds from the exact answer.
The data below was obtained experimentally to determine the BOD of an untreated water sample. Calculate BOD.Day: 1, 2, 4, 6, 8BOD, mg/L: 32, 57, 84, 106, 111
Describe the concept of Gas-driven water samplers.
A sample in a variable head permeameter is 8 cm in diameter and 10 cm high.The permeability of the sample is estimated to be 10 × 10^–4 cm/s. If it is desired that the headin the stand pipe should fall from 24 cm to 12 cm in 3 min., determine the size of the standpipe in cm which should be used. a.1.29 b.5.43 c.3.67 d.4.19
1. THERE IS A LEAK IN A HORIZONTAL 300 MMDIAMETER PIPELINE. UPSTREAM FROM THE LEAK TWOGAGES 600 METER APART SHOWED A DIFFERENCE OF140 ???. DOWNSTREAM FROM THE LEAK TWO GAGES600 METER APART SHOWED A DIFFERENCE OF 126??? . ASSUMING ? = 0.025. HOW MUCH WATER ISBEING LOST FROM THE PIPE. show answer in litre per sec
Q 01 : a)How can you calculate BOD value? What happens if you have a higher BOD value? b)Differences between COD and BOD? Subject is Environmental Engineering
Question: How did you get 25400 on the numerator when solving for S(Potential maximum retention )?
Jonathan Joestar wanted to analyze a sample of water for its mercury content. The suspected concentration of mercury in the water sample is 5 ppm. Which of the following analytical methods should he use for his desired outcome?a. Method D, with a working range of 1-10 ppb, and costs Php 5000 per runb. Method C, with a working range of 10-60 ppm, and costs Php 100 per runc. Method B, with a working range of 1-10 ppm, and costs Php 3000 per rund. Method A, with a working range of 10-60 ppm, and costs Php 1000 per run