Nilo Incorrect.Steady-state creep data taken for an iron at a stress level of 140 MPa are given here:eTextbook and MediaIf it is known that the value of the stress exponent n for this alloy is 8.4, compute the steady-state creep rate at 1300 K and a stresslevel of 86 MPa.HintSave for Later6.6 x 1085x 102h²T(K)11001180Attempts: 2 of 3 used Submit Answer

Answered: Image /qna-images/answer/e09bd7e5-b74e-42f9-8f54-2cbba59354a6.jpg

Steady-state creep data taken for an iron at a stress level of 140 MPa are given here: eTextbook and Media Hint If it is known that the value of the stress exponent in for this alloy is 8.4, compute the steady-state creep rate at 1300 K and a stress level of 86 MPa Save for Later 6.6×10 85x 102 hi T(K) 1100 1180 Attempts: 2 of 3 used Submit Answer

Steady-state creep data taken for an iron at a stress level of 140 MPa are given here: eTextbook and Media Hint If it is known that the value of the stress exponent in for this alloy is 8.4, compute the steady-state creep rate at 1300 K and a stress level of 86 MPa Save for Later 6.6×10 85x 102 hi T(K) 1100 1180 Attempts: 2 of 3 used Submit Answer

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.5P

See similar textbooks

Similar questions

For silver at a tensile stress of 7 MPa and a temperature of 839C , there are two equally contributing creep mechanisms. What are they?
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A load applied to a machine component results in the state of plane stress ?x=80 MPa, ?y=100 MPa, ?xy=60 MPa. The component is made of a brittle high-strength steel that follows the maximum normal stress criterion with ?u=200 MPa. If increasing the load increases each stress component proportionally, determine the percentage increase that can be applied before the component fails.
The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine: The stress of aluminum in segment AC. Answ: 63.66 MPa The stress of aluminum in segment CD. Answ: 13.93 MPa The stress in steel in segment CD. Answ: 39.79 MPa The total deformation of the bar. Answ: 0.29273 mm
2. Please estimate the number of cycles to failure of a steel specimen under tensile fatigue loading with the following parameters. The R ratio is 3, mean stress 200 MPa, yield strength 450 MPa, ultimate tensile strength 560 MPa, Young’s modulus 200 GPa, KIC = 140 MPa . Assume the initial crack length is 0.1 mm.
I5 In a tensile test experiment of carbon steel. a standard specimen (D= 0.505 in. Gauge length=2.0 in & total length 8 in) had a 0.2% offset yield strength of 80.000 psi and engineering strain of 0.010 at the yield strength point Calculate: The load (force) at this point. The instantaneous area of the specimen at this point. c. The true stress at this point. d. The true strain at this point. e. The total length of the specimen. if the load is released at this point.
What is the critical assumption made regarding the area of the particle-to-particle contacts in deriving effective stress?
As shown, an aluminium alloy construction BCD with a circular cross section is fixed at end B and affected by a force of 150 N at the free end D. The diameter of the cross-section a-a is 20 mm. The yield strength of the material is 80 MPa: a) Determine the stresses at point A of the a-a cross-section. As indicated in the picture, draw the stress element in Cartesian coordinates and specify the stress values.(b) Calculate the factor of safety, n for Tresca, and the von Mises yield criterion to see if the structure would yield based on the stresses at point A.(c) In the major stress area, draw the yield loci of both criteria and indicate the operational stress state & why is the Rankine failure criterion inappropriate for aluminium alloys?
Q stress determination in beams., Solid.
A Charpy V Notch (CVN) test was performed on a steel specimen and produced the readings shown in Table . Plot the toughness-versus-temperature relation and determine the temperature transition zone between ductile and brittle behavior.
Sketch the stress-strain curve of the following tension test??? In the tension test of a metal fracture occurs at maximum load. The conditions at fracture were: A = 100 mm and L, = 60 mm, the initial values were: A = 150 mm and L. 40 mm.
What are the consequences of strain hardening on ductility? Discuss the influence of strain-hardening on fatigue behavior.