Steam 90°C 10. A shell-and-tube process heater is to be selected to heat water (Cp 4190 J/kg-°C) from 20°C to 90°C by steam flowing on the shell side. The heat transfer load of the heater is 600 kW. If the inner diameter of the tubes is 1 cm and the velocity of water is not to exceed 3 m/s, determine how many tubes need to be used in the heat exchanger. %3D 20°C Water

Steam 90°C 10. A shell-and-tube process heater is to be selected to heat water (Cp 4190 J/kg-°C) from 20°C to 90°C by steam flowing on the shell side. The heat transfer load of the heater is 600 kW. If the inner diameter of the tubes is 1 cm and the velocity of water is not to exceed 3 m/s, determine how many tubes need to be used in the heat exchanger. %3D 20°C Water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider mixing some of the ice water with the hot water and vice versa so that the two reservoirs are closer to the same temperature. What do you think will happen to the mechanical/thermodynamic efficiency and ideal Carnot efficiency of the heat engine?
What are adiabatic and isothermal processes? Calculate the work done in adiabatic expansion during the working of a reversible heat engine.
Consider a gas turbine of 200 kJ/kg net work, operating under standard cold air assumptions. Determine the thermal efficiency, in %, of the turbine, if it has a regenerator with 90% efficiency.
It is common knowledge that the temperature of air rises as it is compressed. An inventor thought about using this high-temperature air to heat buildings. He used a compressor driven by an electric motor. The inventor claims that the compressed hot-air system is 25 percent more efficient than a resistance heating system that provides an equivalent amount of heating. Is this claim valid, or is this just another perpetualmotion machine? Explain.
Waternearthesurfaceofatropicaloceanhasatemperatureof25°C, while water 700 m beneath the surface has a temperature of 7°C. It has been proposed that the warm water be used as the hot reservoir and the cool water as the cold reservoir of a heat engine. Find the maximum possible efficiency for such an engine.
Determine the expressions for the thermal efficiencies and coefficients of performance for reversible heat engines, heat pumps, and refrigerators.
Determine the isentropic efficiency of the rotary engine and the second law efficiency of therotary engine when the Water vapor inlet a rotary engine at 500 oC temperature and 1200 kPa pressure and exits at 300 oC temperature and 200 kPa pressure.. According to this: (take close temperature of 25 0C)
Figure shows a single-solar-collector panel with a total surface area of 2.97 m^2. The panel receives its energy from the sun at a certain rate. However, thirty-six percent of the incoming energy is lost to the surroundings. The remaining energy is used to heat liquid water from 40 C to 60 C. The water passes through the solar collector with a negligible pressure drop at a rate of 0.0310 ??/?. By neglecting the kinetic and potential energy effects/differences through the pipe lines,a. Determine the outer surface temperature of the Sun.b. How many “Liters” of water at 60oC can the collectorprovide in a 30-min time period?
Water enters the constant 130-mm inside-diameter tubes of a boiler at 7 MPa and 65°C and leaves the tubes at 6 MPa and 450°C with a velocity of 80 m/s. Calculate the velocity of the water at the tube inlet and the inlet volume flow rate
The condenser of a room air conditioner is designed to reject heat at a rate of 15,000 kJ/h from refrigerant-134a as the refrigerant is condensed at a temperature of 40°C. Air (cp = 1005 J/kg·K) flows across the finned condenser coils, entering at 25°C and leaving at 35°C. If the overall heat transfer coefficient based on the refrigerant side is 150 W/ m2·K, determine the heat transfer area on the refrigerant side.
In large steam power plants, the feedwater is often heated in closed feedwater heaters, which are basically heat exchangers, by steam extracted from the turbine at some stage. Steam enters the feedwater heater at 1.6 MPa and 250°C and leaves as saturated liquid at the same pressure. Feedwater enters the heater at 4 MPa and 30°C and leaves 10°C below the exit temperature of the steam. Neglecting any heat losses from the outer surfaces of the heater, determine the ratio of the mass flow rates of the extracted steam and the feedwater heater.
In large steam power plants, the feedwater is often heated in closed feedwater heaters, which are basically heat exchangers, by steam extracted from the turbine at some stage. Steam enters the feedwater heater at 1.6 MPa and 250°C and leaves as saturated liquid at the same pressure. Feedwater enters the heater at 4 MPa and 30°C and leaves 10°C below the exit temperature of the steam. Neglecting any heat losses from the outer surfaces of the heater, determine the reversible work for this process per unit mass of the feedwater. Assume the surroundings to be at 25°C.