Steam flows at 60 m/s through a steam main of 1.6 MPa, 280°C. Four tanks are connected to this main by pipes which are closed by valves, as shown in the Figure. Valve T-280°C Supply line HValve c. Find the final state in tank C. d. Find the final state in tank D. H Valve HValve Tank A, which has heat-conducting walls, is surrounded by a constant-temperature bath at 280°C, and is initially evacuated. Tank B is similar to tank A except that it initially contains steam at 0.8 MPa and 280°C. Tank C has adiabatic walls and is initially evacuated. Tank D has adiabatic walls and initially contained steam at o.8 MPa, 280°C. The valves to the tanks are opened, and closed again when the tanks are filled with steam. a. Find the heat transfer to the steam in tank A. b. Find the heat transfer to the steam in tank B.

Steam flows at 60 m/s through a steam main of 1.6 MPa, 280°C. Four tanks are connected to this main by pipes which are closed by valves, as shown in the Figure. Valve T-280°C Supply line HValve c. Find the final state in tank C. d. Find the final state in tank D. H Valve HValve Tank A, which has heat-conducting walls, is surrounded by a constant-temperature bath at 280°C, and is initially evacuated. Tank B is similar to tank A except that it initially contains steam at 0.8 MPa and 280°C. Tank C has adiabatic walls and is initially evacuated. Tank D has adiabatic walls and initially contained steam at o.8 MPa, 280°C. The valves to the tanks are opened, and closed again when the tanks are filled with steam. a. Find the heat transfer to the steam in tank A. b. Find the heat transfer to the steam in tank B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Box the final answer. Write legibly. Steam is supplied to a fully loaded 1.2 MW turbine at 1.2 mpa with internal energy of 2,620 kJ/kg, specific volume of 0.12 m3/kg and a speed of 120 m/s. The exhaust is at 20 kpa with internal energy of 2,420 kJ/kg, specific volume 8.2 m3/kg, and speed of 220 m/s. The heat loss from the steam in the turbine is 120 kJ/kg, compute the steam flow in kg per minute neglecting the effect of elevation.
With a 50 m^3 capacity, a tank contains steam at 400 degrees Celsius and 4500 kPa. From the tank, steam is vented through a relief valve to the atmosphere until the pressure in the tank falls to 3500 kPa. Assuming the venting process is adiabatic, estimate the steam's final temperature in the tank and the mass of steam vented. (Please help me understand the trial and error part for determining the required amounts by solving.)
17. A fully inflated tire has a volume of 15 ft3. The pressure and temperature of theair in the tire are 65 psia and 75 F, respectively. At this condition, the air intakeneedle is depressed for 3 s and then released. Treating air as an ideal gas and assumingsmall changes in the tire temperature and volume, Find the amount of air that leftthe tire. Assume a discharge coefficient of 0.61 and a flow area of 0.01 in2.
1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet bulb temperature at a rate of 14oo cu ft per min. The surface temperature of the coil is 55 F . If 3.5 tons of refrigeration are available, find the dry bulb and wet bulb temperatures of the air leaving the coil. Assume sea level pressure.
The movement of 4.2 kilograms of gas through an isentropic pump requires 85 kilowatts of power. Find the power saved or increased if the process is changed to be isothermal and the Cv=0.886 kJ/kg-K and the Cp=1.758 kJ/kg-K. The final pressure is 22 psia, and the initial pressure was 850 mmHg, and the initial temperature was 38°C.
Q29. Steam enters the condenser of a power plant at 3 psia and a quality of 95% with a ratio ofmass flow of 40,000 lbm/hr. It will be cooled with water from a nearby river, which will circulate through the tubes inside the condenser. In order to avoid thermal pollution, the river water is not allowed to suffer from an increase in temperature.temperature greater than 18°F. If steam is to leave the condenser as a saturated liquid at 3 psia, determine how many times the mass flow rate of steam will be the mass flow rate of water, as well as the heat transfer from one system to the other.
R-134a enters a compressor as a saturated vapor at 80 kPa and exits at a pressure of 400 kPa. If 44 kJ/kg of work is required and 5 kJ/kg of heat is lost to the surroundings. What is the outlet temperature. Round your answer to the nearest whole number.
50 kg water per minute is to be heated from 30°C to 50°C by passing through a pipe of 2cm diameter. the pipe is heated by condensing the system keeping its inner surface at 100°C . find the length of pipe required. Take the following properties of water at mean bulk temperature of 40°C, density= 965 kg/m^3, v= 0.33*10^-6 m^2/sec , Cp= 4200J/kgK ,k= 0.585W/mK
5.) By traveling through a bass tube, 2.5 cm O.D. and 2.2 cm I.D., which is surrounded by steam at 55 kPa and 90% quality, 9.4 kg/s of water is heated from 15oC to 60oC. Assume the inside unit convective coefficient is 2000 W/m2-K, and the outside unit convective coefficient is 7950 W/m2-K. Determine (a) the length of tube required; (b) the steam supply in kg/h if no subcooling occurs.
Given that μ = 0.25Katm−1 for nitrogen, calculate the value of its isothermal Joule–Thomson coefficient. Calculate the energy that must be supplied as heat to maintain constant temperature when 15.0 mol N2 flows through a throttle in an isothermal Joule–Thomson experiment and the pressure drop is 75 atm.
Water at 90C is being pumped from a large storage tank at 1 atm abs at a rate of 0.189 m3/min by a pump. The motor that drives the pump supplies energy to the pump at a rate of 2 hp. The water pumped through a heat exchanger, where it gives up 700 kW of heat and is then delivered to a large open storage tank at an elevation of 20 m above the first tank. What is the final temperature of the water to the second tank? Neglect kinetic energy.
A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 285 psf, and 270 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,255 psf and 750 degrees Fahrenheit. Assuming that the velocity found at the inlet is 6,285 feet per minute and the Heat supplied is 580 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 6 minutes?