Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C, and 80 m/s and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 11.4 kg/s. The properties of the steam are vy = 0.086442 m/kg, h = 3446 kJ/kg, and h2 = 2437.7 kJ/kg. %3D

Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C, and 80 m/s and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 11.4 kg/s. The properties of the steam are vy = 0.086442 m/kg, h = 3446 kJ/kg, and h2 = 2437.7 kJ/kg. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P23. Steam enters an insulated nozzle with negligible velocity, 200 psi and 500°F. Steam exits at 100 psi and 400°F.For steady-state operation and neglecting potential energy effects, determine the velocity of the steamleaving the nozzle in ft/s.
Problem 2 – Heat Pump Thermodynamic Analysis Refrigerant-134a enters the condenser of a residential heat pump at 800 kPa and 50°C at a rate of 35 L/min and leaves at 750 kPa subcooled by 3°C. The refrigerant enters the compressor at 200 kPa superheated by 3°C. Neglecting changes in kinetic and potential energy and any stray heat transfer, please answer the following. a. Create a schematic of the cycle, use the same numbers used in your textbook for the inlet and exit states of each device, and include the energy exchanges between the cycle devices and the surroundings. b. Sketch the cycle processes on a T-s diagram. c. Determine the isentropic efficiency of the compressor. d. Compute the rate of heat supplied to the heated room. e. Determine the COP of the heat pump.
A certain Geothermal Power Plant shows that 1,700,000 kg/hr of pressurized ground water is available at 17.5MPa and 330°C. The water will be throttled to a pressure of 1.7MPa to produce wet steam and this mixture will be passed through a water separator to remove the water droplets so that saturated steam at 1.7MPa is available at the entrance of the Turbine. Other data are as follows: Discharge Pressure of turbine = 85kPa-Vac; Turbine Efficiency = 73%. Mechanical Loss = 2% of shaft power. Generator Efficiency = 95%. Determine the following: 1.The mass flow rate, in kg/min, of steam entering the turbine. a. 153,720 b . 76,858 c. 38,430 d. 19,200 e. 9,350 2. The maximum amount of power, in kW, that the plant can generate. a. 38,430 b. 19,200 c. 76,858 d. 9,350 e. 153,720
Define the adiabatic process?
7.15. A steam turbine operates adiabatically at a power level of 3500 kW. Steam enters the turbine at 2400 kPa and 500°C and exhausts from the turbine as saturated vapor at 20 kPa. What is the steam rate through the turbine, and what is the turbine efficiency?
Water flows through a horizontal coil heated by steam condenaing on the outside. If the inlet pressure and temperatire are 2 atm and 160°F (state 1) and at the exit 1 atm and 220 °F (state 2), calculate the heat added to the coil per pound mass of water. The entering velocity is 5 ft/s, and the leaving, 500 ft/s. Data: H1=127.9 Btu/lb, H2=1154.4 Btu/lbA. 1031 Btu/lbB. 1042 Btu/lbC. 1048 Btu/lbD. 1052 Btu/lb
Define the Reversible Adiabatic Compression
Your second customer wants to determine the dissipated electrical power by a personal computer, which has a fan that draws 5 L/s of air at 101.325 kPa and 21°C through the box containing the CPU and other components. After that air leaves at 101.325 kPa and 30 °C. Part 1Derive the steady flow energy equation (SFEE) from the first principles. You are required to show all the steps in deriving the SFEE and using both the principles of mass and energy conversation.Part 2Produce specific steady state energy equation (SFEE) by stating all the stated assumption in this equipment in order to be used in later stages without further analysis. Then calculate the pump power.Part 3Apply the short form to determine the dissipated electrical power by the personal computer.
Write legibly so i can understand 3. The turbine section of a Brayton cycle gas turbine receives hot compressed air at 150 psia and 2100 o R, expands it to 15 psia and develops a gross output of 15,000 HP. Air enters the compressor at 500 R. Determine: d.) thermal efficiency, e) mean effective pressure (psia)
THERMODYNAMICS A 1.5-kW power output is produced by a small, high-speed turbine that runs on compressed air. The entrance state is 400 kPa and 52 degrees celcius, whereas the exit state is 150 kPa and -43 degrees celcius. Determine the needed mass flow rate of air through the turbine assuming low velocities and an adiabatic process.
A turbine, operating under steady-flow conditions, receives X1 kg of steam per hour (For X1 refer Table. 1). The steam enters the turbine at a velocity of 3000 m/min, an elevation of 5 m and a specific enthalpy of 2787 kJ/kg. It leaves the turbine at a velocity of 6000 m/min, an elevation of 1 m and a specific enthalpy of 2259 kJ/kg. Heat losses from the turbine to the surroundings amount to 16736 kJ/h. Determine the power output of the turbine.
Define the Reversible Adiabatic Expansion