Steam inters a turbine at 21 kg/s as shown in the figure, find the exit temperature?T2=? sat. vap.Q= 639 kWTurbineW= 12240 kW1.6 MPa350°C Q1: Steam inters a turbine at 21 kg/s assat. vap.shown in the figure, find the exitQ= 639 kWtemperature.TurbineW= 12240 kw1.6 MPa350°C

Answered: Image /qna-images/answer/6ae01423-3b6b-424f-9421-41de56d397a6.jpg

Answered: Steam inters a turbine at 21 kg/s as…

Engineering

Mechanical Engineering

Steam inters a turbine at 21 kg/s as shown in the figure, find the exit temperature?T2=?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: 2-Calculate the stagnation temperature and pressure for the following substances flowing through a…

A: Given DataHeliumP=0.25MPaT=508CV=240m/sNitrogenP=0.15MPaT=508CV=300m/sSteamP=0.1MPaT=3508CV=480m/s

Q: H.w : nitrogen gas flows into a convergent nozzle at 200 kpa 400 K and very low velocity it flows…

Q: An air compressor takes in 12m3 /min of air (measured at atmospheric conditions of 101.3 kPa, 15o c)…

A: Given data An air compressor takes in 12m3 /min of air (measured at atmospheric conditions of 101.3…

Q: Consider the flow of air in a duct, which shown in the figure. The flow is adiabatic between…

Q: Consider steady adiabatic airflow in a duct. At section B,the pressure is 600 kPa and the…

A: Given data

Q: A steam turbine takes in steam at the rate of 6000 kg/h and its power output is 800 kw. neglect any…

Q: 1)Steam expands at a rate of 40,000 kg/h in a turbine. At the inlet, 8 MPa pressure and 40 kPa…

A: Given data:

Q: A steam turbine carrying a full load of 46 MW uses 77.7 kg/s of steam. The turbine efficiency is…

A: Given: A steam turbine Turbine load = 46 MW ms = 77.7 kg/s of steam turbine efficiency = 78%…

Q: An air compressor takes air at 100 Kpa and discharges to 600 Kpa. If the volume flow of discharge is…

A: Given : P1 = 100 KPa P2 = 600 KPa volume flow of discharge, V.2 = 1.2 m3/sec To find : capacity of…

Q: At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 kJ/kg. In addition, the velc…

Q: find the work done by 0.15kg of air in a isobraic compression from t1=258k to t2=367 at 203kpa

Q: A 32 m high down Comer-tank system operates lloo bar if the exit quality of the steam is what will…

A: Given Volume, V = 32 m3 Initial pressure, P1 = 100 bar Quality, x = 0.5…

Q: HW1: A gas flows through a horizontal pipe with cross-sectional area of 30 cm². At certain point,…

Q: Nitrogen gas flows into a convergent nozzle at 200 kPa, 400 K and very low velocity. It flows or…

A: Given:Inlet conditions,P1=200 kPaT1=400 Koutlet conditions,P2=100 kPaT2=330 K

Q: Qs: Air flows steadily through a horizontal nozzle. At the nozzle inlet, the velocity is 6 m's and…

A: Bernoulli's Equation is a type of Energy equation where sum of pressure head, kinetic energy head…

Q: Q: An air is compressed from pressure 120 to 200 KPa and its initial volume is 0.2 m3 at constant…

Q: Compressed air is discharged through the converging nozzle, as shown in Figure P3.7. The tank…

Q: Steam flows into a turbine at a rate of 2 kg/s at 3MPa and 400C. It comes to an end at 300kPa. The…

Q: A pump delivers 50 liters/sec of water. The intake to the pump is 75m below the final discharge. The…

Q: Q3/ Consider Steam is cooled from 550 to 111.4 °C. Assume that during this process the pressure…

A: GIVEN DATA- T1=550'C P1=300KPa T2=11.4'C P2=150KPa WE HAVE TO FIND ENTROPY CHANGE

Q: mass flow rate of the air (lbm/s).

A: Given data as per the question For a compressor work-done = 10hp =-5500 lbf ft/s (-ve sign represent…

Q: The water from the feed pump enters the boiler at 1125 psia and 280 °F. Find the following…

Q: During the execution of a reversible non-flow process the work is -156.2 KJ if V1=0.845 and the…

Q: Water is passing from the nozzle having an inlet area is 0.08 m2 and velocity is 5 m/s, the outlet…

A: Given: Inlet area, A1=0.08 m2 Outlet area, A2 =0.05 m2 Velocity in the inlet of nozzle, V1= 5 m/s

Q: Q2: A nozzle is a device for increasing the velocity of steadily flowing stream of fluid. At the…

A: GIVEN DATA- A NOZZLE GIVEN INLET CONDITION h1=3025 KJ/Kg , C1=60m/s , Z1=0m , A1=0.1m2 , v1=0.19…

Q: Q3: A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the…

A: Given data: The enthalpy at the entry is h1=3025 kJ/kg The enthalpy at the exit is h2=2790 kJ/kg The…

Q: 6. From number 3, if the gas tank accident happened on top of Mt. Everest's summit where patm is…

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: Express the Bernoulli equation in three different ways using (a) energies, (b) pressur

A: Given: Bernoulli,s equation

Q: A syringe in the figure contains fluid of s.g. 1.05. If the plunger is pushed in steadily at 0.125…

A: To find : determine exit velocity . Given : specific gravity ς=1.05 initial velocity v1=0.125 in/s…

Q: Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume at inlet…

Q: Water vapor at 400 temperature and 3 mpa pressure enters an adiabatic nozzle at a speed of 40 m/s…

Q: At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 kJ/Kg. In addition, the…

Q: A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid, At the inlet…

Q: Q4) Considering water at 30°C flowing over a flat plate 1 m × 1 m at 10°C with a free stream…

Q: o At the inlet to a certain nozzle, the enthalpy of the gas is 3000 kJ/kg and velocity is…

A: In this problem, we know that the enthalpy of the gas at the input of a certain nozzle is 300 kJ/kg…

Q: The compressor (10 hp) pulls in gas at 150 psi and 10.5 ft3/lbm velocity at the entrance is 2 ft/s,…

A: Given Data, P1 =Pressure at entrance of the compressor =150 Psi = 1034.214 KPa (1Psi =6.895…

Q: Air compressor takes air of mass flow rate (9kg/min) at (100kPa) and (300K). Air leaves the…

A: Write the given value using suitable variables. Here m signifies mass flow rate, P1 signifies inlet…

Q: urbine through a duct with a diameter of 0.5 m at 10 MPa , 600 °, and 100 m/s . It exits the turbine…

Q: In a steam turbine, water vapor enters at a temperature of 450C and a pressure of 2.5 MPa, at a…

A: The device used in the power plant which is used to convert enthalpy with the working fluid into…

Q: Q1. During a steady flow process in an open system the velocity of the fluid is increase from100 to…

Q: R-134a is throttled in a line flowing at 25°C, 750 kPa with negligible kinetic energy to a pressure…

A: Given: Inlet temperature T1=25°C or 298KInlet pressure P1=750kPaOutlet pressure P2=165kPa

Q: A 20 × 25 cm reciprocating compressor has a 4% clearance and operates at 550 rpm. The compressor…

Q: An air compressor absorbs 1000 kg of air per hour at a pressure of 100 kPa and 500 kPa it presses on…

Q: steam turbine receives a steam flow of 1.35 kg/s and the power output is 500 kW. The heat loss from…

Q: Air at 400K and 500kPa flows to a turbine at a rate of 5kg/s. The pressure at the outlet of the…

A: Given data:

Q: Q3: A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the…

Question

Steam inters a turbine at 21 kg/s as shown in the figure, find the exit temperature?T2=?

sat. vap.
Q= 639 kW
Turbine
W= 12240 kW
1.6 MPa
350°C

Q1: Steam inters a turbine at 21 kg/s as
sat. vap.
shown in the figure, find the exit
Q= 639 kW
temperature.
Turbine
W= 12240 kw
1.6 MPa
350°C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the turbine output of 100m head and delivering 1 cu. m/ sec in a hydro electric power plant if turbine efficiency is 88%?
a hydraulic turbine receives water froma reservor at an elevation of 100 meter above it. what is the minimum water flow in (kg/sce) to produce a steady turbine output of 50 mw?
A turbine extracts water from a 25 m high reservoir, if the flowrequirement is 10000 m3/hr, what is the generated power in kW ifthe efficiency is 75%?
25. A wind turbine having an efficiency of 35% and rotor diameter of 33 m is exposed to air flowing at a speed of 6 m/s. Find the power developed by the turbine. Assume ρ = 1.2 kg/m3. [Ans.: 38.8 kW].
A group of engineers is designing a new hydroturbine by scaling up an existing one. The existing turbine (turbine A) has diameter DA = 1.50 m, and spins at n.A = 150 rpm. At its best efficiency point, V.A = 162 m3 /s, HA = 90.0 m of water, and bhpA = 132 MW. The new turbine (turbine B) will spin at 120 rpm, and its net head will be HB = 110 m. Calculate and compare the efficiency of the two turbines. They should be the same since we are assuming dynamic similarity. However, the larger turbine will actually be slightly more efficient than the smaller turbine. Use the Moody efficiency correction equation to predict the actual expected efficiency of the new turbine. Discuss.
An air compressor is to compress 50 m^3/min from 19.666 kPa to 598.491 kPa. Assuming condition is ideal, and n=1.3 What will be the work in kW due to 3 staging Answer in whole number
A group of engineers is designing a new hydroturbine by scaling up an existing one. The existing turbine (turbine A) has diameter DA = 1.50 m, and spins at n.A = 150 rpm. At its best efficiency point, V.A = 162 m3 /s, HA = 90.0 m of water, and bhpA = 132 MW. The new turbine (turbine B) will spin at 120 rpm, and its net head will be HB = 110 m. Calculate the diameter of the new turbine such that it operates most efficiently, and calculate V.B and bhpB.
A hydro-electric plant discharge water at the rate of 0.75 m3/s and enters the turbine at 0.35 mps with a pressure of 275 kpa. Runner inside diameter is 550 mm. Speed at 320 rpm and the turbine efficiency is 88%. Find the turbine speed factor.
NOTE THE ANSWER SHOULD BE 10.75m3/s Find the flow rate of water through the sytem shown for the turbine to produce 20 kW. Neglect friction in your calculations NOTE: THE ANSWER SHOULD BE 10.75m3/s
Find the flow rate of water through the sytem shown for the turbine to produce 20 kW. Neglect Friction in your calculations (1) Q=10.75m3/s (2) P=204kw/273hp
A Kaplan turbine working under a head of 43 m deve-lops 15,400 B.H.P. The dia of theboss is 0"3 times the dia ofrunner. Determine the speed and dia of runner, if speed ratio is2, flow ratio as 0-65 and overall efficiency as 91%.
b. The discharge pressure of an air compressor is 6 times the suction pressure. If the volumeflow rate at the suction is 0.86 cubic meters per second, what is the compressor power (kW)for n = 1.38 and suction pressure is 101 kPaa?