Q2: A nozzle is a device for increasing the velocity of steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the veleeity is 60 m/s. At the exit from nozzle the enthalpy is 2790 kJ/kg. The nozzle is vertical with a 0.5 m height; ignore the heat loss from it. Find the velocity at the nozzle exit and the rate of how of fluid if the inlet area is 0.1 m² and the specific volume at inlet is 0.19 m²/kg.

Q2: A nozzle is a device for increasing the velocity of steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the veleeity is 60 m/s. At the exit from nozzle the enthalpy is 2790 kJ/kg. The nozzle is vertical with a 0.5 m height; ignore the heat loss from it. Find the velocity at the nozzle exit and the rate of how of fluid if the inlet area is 0.1 m² and the specific volume at inlet is 0.19 m²/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A horizontal pipe has a sudden expansion from diameter 8 cm to diameter 16 cm as shown in Figure Q2(b). The velocity and pressure of the water in the inlet of sudden expansion is 10 m/s and 410 kPa respectively. Based on Table 2 and setting given to you, determine the pressure at the outlet of the sudden expansion.
2. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079ft/cu. ft and discharges it with a density of 0.304 lb/cu. ft. At the suction, P 1 = 15 Psia; atdischarge, P 2 = 80 psia. The increase in the specific internal energy is 33.8 BTU/lb and the heattransferred from the air by cooling is 13Btu/lb. Determine the work on the air in BTU/min and inhp. Neglect kinetic energy. 3 decimal in final answer pls
I am studying for an exam this week, and I want to check my steps and answers for this one problem. Air enters a nozzle steadily with a density of 2.21 kg/m^3 and velocity of 40 m/s and leaves at 180 m/s with a density of 0.762 kg/m3. If the nozzle inlet has an area of 90 cm^2, determine: a) The Volumetric flow rate at the in let (m^3/s) b) The Mass flow rate (kg/s) through the nozzle; c) The exit area of the nozzle (cm^2)
a gas expands in a piston from initial pressure of 1000 kPa and an initial volume of 0.15 cubic meter to a final pressure of 200 kPa while following the process described by p=aV + b, where a =- 1600 kPa/cubic meter and b is a constant. calculate the work performed.
Solve the problem. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 lb/cu ft and discharges it with a density of 0.304 lb/cu ft. At the suction, pressure is 15 psia, at discharge pressure is 80 psia. The increase in the specific internal energy is 33.8 Btu/lb and the heat transferred from the air by cooling is 13 Btu/lb. Determine the work on the air in Btu/min and in hp. Neglect change in kinetic energy.
A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume at inlet is 0.19 m3/kg, find the rate of flow of fluid (iii) If the specific volume at the nozzle exit is 0.5 m3/kg, find the exit area of the nozzle.
A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 Ib/ft^3 and discharge it with density of 0.304 lb/ft 3. At the suction P1-15 psia: at discharge. P2-80 psia. The increase in the specific internal energy is 33.8 BTU/b and the heat transferred from the air by cooling is 13 BTU/lb. Determine the work on the air in BTU/lb. Neglect change in kinetic energy
A garden hose attached with a nozzle is used to fill a 20-gal bucket. The inner diameter of the hose is 1 in and it reduces to 0.4 in at the nozzle exit. If the average velocity in the hose is 6 ft/s, determine (a) the volume and mass flow rates of water through the hose, (b) how long it will take to fill the bucket with water, and (c) the average velocity of water at the nozzle exit.
At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. i) Find the velocity at the nozzle exit. ii) If the inlet area is 0.10 m2 and specific volume at inlet is 0.19 m3/kg. Determine the exit fluid density (kg/m3) if thea area at the exit is one-tenth of the area at the inlet
A reciprocating compressor draws in 500 gal per minute of air whose density is 0.079 lbm/cu ft and discharges it with density of 0.304 lbm/cu ft. At the suction, p1 = 15 psia; at discharge, p2 = 80 psia. The increase in the specific internal energy is 33.8 Btu/lbm and the heat transferred from the air by cooling is 20 Btu/lbm. Determine the work on the air in Btu/min and in hp. STEP BY STEP EXPLANATION PLS
During the execution of a reversible non flow process the work Is -156.2 KJ. If V1 =0.845 cubic meter and the pressure varies as P= -730V+690 KPaa where V is in cubic meter, Determine the final volume
⦁ 0.1 m3 rigid tank (tank volume is constant) contains water at 200ºC and 500 kPa at the beginning. Then the tank is cooled and heat loss (Q) of the system is 554.21 kJ. The final pressure (P2) of the tank is 15 kPa. During this process, determine, the final specific internal energy (u2) and the final temperature (T2) of the tank.