Steam is admitted to the twin cylinder of an engine in such a manner that the average pressure is 120 psi. The diameter of the piston is 10 in. and the length of stroke is 12 in. The engine is making 300 rpm with a mechanical efficiency of 90%. Calculate the ideal generator hp output if the generator has an efficiency of 80%

Steam is admitted to the twin cylinder of an engine in such a manner that the average pressure is 120 psi. The diameter of the piston is 10 in. and the length of stroke is 12 in. The engine is making 300 rpm with a mechanical efficiency of 90%. Calculate the ideal generator hp output if the generator has an efficiency of 80%

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

Steam is admitted to the twin cylinder of an engine in such a manner that the average pressure is 120 psi. The diameter of the piston is 10 in. and the length of stroke is 12 in. What is the horse power of the engine when it is making 300 rpm?
The specific speed of turbine is 85 rpm and running at 450 rpm. The effective head is 20m and generator efficiency is 90%. Compute the maximum power delivered by the generator in kW 734.94 934.94 834.94
An impulse turbine of 3 m diameter is rated at 10000 kW at 300 rpm under a head of 500 m. The turbine is operated under the head of 400 m. What is the power developed?
For a single stage impulse turbine with rotor diameter of 2 m and a speed of 3000 rpm when the nozzle angle is 20°,calculate the optimum velocity of steam in m/s.
The compression ratio in a gasoline engine is 8. The total cylinder volume of the engine (for the bottom dead point) is 600 ml, and air enters the cylinders at a temperature of 20 ° C and a pressure of 100 kPa andThe maximum temperature of the cycle is known as 1500 ° C. a) Calculate the heat input in the cycle in kJ. b) Calculate the thermal efficiency of the cycle c) Calculate the power generated in the cycle.
A fan produces 200Pa at an impeller speed of 1000rpm. What is the change in pressure if the impeller speed was increased to 2000rpm? Show complete solution.
At the power station, a Pelton wheel produces 1260kW under a head of 610m. The loss of head due to pipe friction between the reservoir and nozzle is 46m. The buckets of the Pelton wheel deflect the jet through an angle of 1658, while relative velocity of the water is reduced by 10% due to bucket friction. The bucket/jet speed ratio is 0.46. The bucket circle diameter of the wheel is 890mm and there are two jets. Find the theoretical hydraulic efficiency, speed of rotation of the wheel, and diameter of the nozzle if the actual hydraulic efficiency is 0.9 times that calculated above. Assume nozzle velocity coefficient, Cv = 0.98 Show complete solution.
Design an axial flow turbine stage to meet the following expectations. The inlet conditions are Tor=2000 R, Por=200 psia, and it is expected to produce 1500 hp. Note that the answer will not be unique.
A Kaplan turbine delivering 40 MW works under a head of 35 m and runs at 167 rpm.The hub diameter is 2.5 m and runner tip diameter is 5 m. The overall efficiency is 87%.Determine the blade angles at the hub and tip and also at a diameter of 3.75 m. Also find the speed ratio and flow ratio based on tip velocity. Assume ηH = 90%. Outlet blade angle at the mean diameter
An inward flow turbine is supplied with 245L of water per second and works under a total head of 30m. The velocity of wheel periphery at inlet is 16m/s. The outlet pipe of the turbine is 28cm in diameter. The radial velocity is constant. Neglecting friction, calculate (1) The vane angle at inlet (2) The guide blade angle (3)Power Show schematic diagram ang provide solutions.
a. The effective head in meters b. the turbine power in MW if the turbine efficiency is 80%. c. The annual energy that the plant can produce in kW-hr per year if its annual operation is 348 days. The generator efficiency is 92%
A Kaplan turbine develops 10,000kW under an effective head 8m. The overall efficiency is 0.86, the speed ratio 2.0, and flow ratio 0.60. The hub diameter of the wheel is 0.35 times the outside diameter of the wheel. Find the diameter and speed of the turbine. Show schematic diagram and provide solutions.